Portland Area polishing
#1
Old School Member
Thread Starter
Join Date: Feb 2001
Location: Vancouver, Wa, USA
Posts: 640
Likes: 0
Received 0 Likes
on
0 Posts
Portland Area polishing
I'm lookin for someone to polish my UIM, TB, Water pump housing, termostat in the Portland metro area, any recommendations? prices?
#3
Lift Off in T-Minus...
iTrader: (6)
Haha, good luck with that. Do a google search for local shops that do it. There is a tonne of them.
Wait, I'll help your lazy ***, 518 locations:
http://maps.google.com/maps?f=q&hl=e...=UTF8&t=h&z=11
Wait, I'll help your lazy ***, 518 locations:
http://maps.google.com/maps?f=q&hl=e...=UTF8&t=h&z=11
#4
Old School Member
Thread Starter
Join Date: Feb 2001
Location: Vancouver, Wa, USA
Posts: 640
Likes: 0
Received 0 Likes
on
0 Posts
Haha, good luck with that. Do a google search for local shops that do it. There is a tonne of them.
Wait, I'll help your lazy ***, 518 locations:
http://maps.google.com/maps?f=q&hl=e...=UTF8&t=h&z=11
Wait, I'll help your lazy ***, 518 locations:
http://maps.google.com/maps?f=q&hl=e...=UTF8&t=h&z=11
Good help A-hole.
#5
Lift Off in T-Minus...
iTrader: (6)
Lol, can't take a joke, man lighten up.
Here's are some good ones, this is where the fabrication shop at my work outsources all their polish work:
Metal Polishing By Timothy
4415 NE 148th Ave, Portland, OR
(503) 253-5294
http://maps.google.com/maps?f=q&hl=e...h&z=11&iwloc=A
Russell Leininger Polishing
627 SE Division Pl, Portland, OR
(503) 232-9109
http://maps.google.com/maps?f=q&hl=e...h&z=15&iwloc=A
Specialty Finishes LLC
5555 N Channel Ave, Portland, OR
(503) 247-1727
http://maps.google.com/maps?f=q&hl=e...h&z=12&iwloc=A
Here's are some good ones, this is where the fabrication shop at my work outsources all their polish work:
Metal Polishing By Timothy
4415 NE 148th Ave, Portland, OR
(503) 253-5294
http://maps.google.com/maps?f=q&hl=e...h&z=11&iwloc=A
Russell Leininger Polishing
627 SE Division Pl, Portland, OR
(503) 232-9109
http://maps.google.com/maps?f=q&hl=e...h&z=15&iwloc=A
Specialty Finishes LLC
5555 N Channel Ave, Portland, OR
(503) 247-1727
http://maps.google.com/maps?f=q&hl=e...h&z=12&iwloc=A
Last edited by afgmoto1978; 05-07-08 at 10:31 AM.
#6
Junior Member
Join Date: Feb 2004
Location: Eugene, Oregon
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
The only place I found in Portland was "Metal Polishing by Timothy" located east of the airport.
They did my wheel lips, did a DAMN good job and were decent price.
They are about $57 an hour but are fast.
Polishing is all they do. They seem a little sketch at first but they do the OEM polishing for Kenworth.
here is their website:
http://www.metalpolishingbytimothy.com/
their hours are 6am to 3pm so you have to work around them.
They are totally worth it.
little hint: I would take steel wool to your parts first.. clean them up. The less they have to do, the less it will cost you. And they dont strip paint. Again ALL they do is polishing.
#7
Old School Member
Thread Starter
Join Date: Feb 2001
Location: Vancouver, Wa, USA
Posts: 640
Likes: 0
Received 0 Likes
on
0 Posts
Lol, can't take a joke, man lighten up.
Here's are some good ones, this is where the fabrication shop at my work outsources all their polish work:
Metal Polishing By Timothy
4415 NE 148th Ave, Portland, OR
(503) 253-5294
http://maps.google.com/maps?f=q&hl=e...h&z=11&iwloc=A
Russell Leininger Polishing
627 SE Division Pl, Portland, OR
(503) 232-9109
http://maps.google.com/maps?f=q&hl=e...h&z=15&iwloc=A
Specialty Finishes LLC
5555 N Channel Ave, Portland, OR
(503) 247-1727
http://maps.google.com/maps?f=q&hl=e...h&z=12&iwloc=A
Here's are some good ones, this is where the fabrication shop at my work outsources all their polish work:
Metal Polishing By Timothy
4415 NE 148th Ave, Portland, OR
(503) 253-5294
http://maps.google.com/maps?f=q&hl=e...h&z=11&iwloc=A
Russell Leininger Polishing
627 SE Division Pl, Portland, OR
(503) 232-9109
http://maps.google.com/maps?f=q&hl=e...h&z=15&iwloc=A
Specialty Finishes LLC
5555 N Channel Ave, Portland, OR
(503) 247-1727
http://maps.google.com/maps?f=q&hl=e...h&z=12&iwloc=A
thanks for the (eventual) help)
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
gabescanlon
3rd Generation Specific (1993-2002)
2
09-15-15 06:57 AM