help ANY INPUT WOULD BE OK, THANKS
#1
Junior Member
Thread Starter
Join Date: Jan 2015
Location: NJ
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
help ANY INPUT WOULD BE OK, THANKS
my fb was re painted a few yrs ago by previous owner and had taken the front windshield off........well now when it rains it gets wet inside and not a little bit either i have to constantly wipe the water drops coming from the whole top window and it sucksssss
what can i use to seal the window. with out having to remove it.
alsooo my washer fluid is full but wont shoot out the water,,, at this point i dontt need it lol but i would like to get it working again what are some trouble shootings i can do???
thanks in advanced.
what can i use to seal the window. with out having to remove it.
alsooo my washer fluid is full but wont shoot out the water,,, at this point i dontt need it lol but i would like to get it working again what are some trouble shootings i can do???
thanks in advanced.
#2
Doritos & Dual Sports
iTrader: (8)
take the trim off and you can attempt to use a sealer like flex seal or something, but the only CORRECT way to do it would be to take the windshield off and have it resealed correctly.
washer bottles are notorious for going up, really just replace it is the only thing ive ever seen
might want to clean the lines too, make sure theres no dirt stuck in them
washer bottles are notorious for going up, really just replace it is the only thing ive ever seen
might want to clean the lines too, make sure theres no dirt stuck in them
#3
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes
on
91 Posts
And if you've never removed and reinstalled a windshield, I'd suggest calling a mobile glass company. Not ridiculously expensive and they have the experience to do it without breaking the windshield in about an hours time.
#4
Either take it to a glass shop or do the DIY method
I have replaced 2 windshield myself. I have done a lot of bodywork in the past so what I use to remove and Install the glass is 2 big "Bondo" brand suction cups.
1.) Pull away the trim or molding around your vehicle, it is important to not damage this seal or water will always manage to seep in.
2.) Get inside the car, Take a knife and start to cut around the whole border. Spray any sort of lubricant to make this step easier.
3.) Mount both suction cups, get a friend to help carefully push from inside the vehicle and try to remove it from bottom to top. (Works best I find)
Walla your done on removing it. I'm going to guess that the silicone around the window isn't done properly. If you want to permanently remove your issue I would not go for a patch job and try to add silicone. I would remove, dry the wet spot out, re silicone. Hope that helped.
I have replaced 2 windshield myself. I have done a lot of bodywork in the past so what I use to remove and Install the glass is 2 big "Bondo" brand suction cups.
1.) Pull away the trim or molding around your vehicle, it is important to not damage this seal or water will always manage to seep in.
2.) Get inside the car, Take a knife and start to cut around the whole border. Spray any sort of lubricant to make this step easier.
3.) Mount both suction cups, get a friend to help carefully push from inside the vehicle and try to remove it from bottom to top. (Works best I find)
Walla your done on removing it. I'm going to guess that the silicone around the window isn't done properly. If you want to permanently remove your issue I would not go for a patch job and try to add silicone. I would remove, dry the wet spot out, re silicone. Hope that helped.
#5
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
Dude had the old one out in about 5 minutes.
If the car has been repainted then get someone to do it that does it for a living!
I hate screwing up my stuff!