a_reyes1014

iTrader: (1)

hey can anyone help with a base map for some 800 primaries and 1000 secondaries? its a street port with a t60 turbo turbo 2 motor.

rx72c

iTrader: (8)

Idle Map
Screen 1

30" ~ 1.38
25" ~ 1.48
20" ~ 1.33
15" ~ 1.71
10" ~ 1.71
05" ~ 1.62
00" ~ 2.00
2-20psi ~ 4.95

Load Map
Screen 3

30" ~ 0.95
25" ~ 1.19
20" ~ 1.33
15" ~ 1.71
10" ~ 2.14
05" ~ 2.57
00" ~ 3.2
2psi ~ 2.7
4psi ~ 3.5
6psi ~ 4.1
8psi ~ 4.4
10psi ~ 4.9
14psi ~ 5.5
16psi ~ 5.9
18psi ~ 6.5
20psi ~ 7

RPMwot Map Screen 17

5000 ~ 05
5500 ~ 08
6000 ~ 08
6500 ~ 10
7000 ~ 11
7500 ~ 11
8000 ~ 11
9000 ~ 12

The rest are zero

RPMcrs Screen 18

1000 ~ -12
1500 ~ -11
2000 ~ -12

THe rest are zero



Pump Map
Screen 19

Pump2Start ~ 2000
Pump1Amt ~ 15
Pump1Pulse ~ 04
Pump1Trig ~ 14
Pump1Stop ~ 00
Pump1Adv ~ 05

Pump2Time ~ 10
Pump2Amt ~ 30
Pump2Trig ~ 16
Pump2Stop ~ 00
Pump2Adv ~ 05

PumpDwell ~ 3.00
PumpTimers ~ No
Pump1Sync ~ No
PumpSpare ~ 00
PumpCold ~ 00

Water Map
Screen 20

-25 ~ 0
-17 ~ 70
-9 ~ 60
-01 ~ 50
05 ~ 45
11 ~ 45
18 ~ 42
24 ~ 34
31 ~ 26
38 ~ 24
46 ~ 19
60 ~ 12
68 ~ 06
82 ~ 0
99 ~ 0
124 ~ 0

Air_t Map
Screen 21

-25 ~ 0
-17 ~ 8
-9 ~ 6
-1 ~ 5
5 ~ 4
11 ~ 3
18 ~ 3
24 ~ 0
31 ~ 0
38 ~ 0
46 ~ 0
60 ~ 0
68 ~ 0
82 ~ 0
99 ~ 0
124 ~ 0

Crank Map
Screen 22

-25 ~ 72
-17 ~ 72
-9 ~ 72
-1 ~ 67
5 ~ 62
11 ~ 57
18 ~ 50
24 ~ 41
31 ~ 31
38 ~ 26
46 ~ 20
60 ~ 15
68 ~ 5
82 ~ 0
99 ~ 0
124 ~ 0

t*rpm
Screen 23

Idle ~ 05
1000 ~ 10
1500 ~ 15
2000 ~ 20
2500 ~ 25
3000 ~ 25
3500 ~ 25
4000 ~ 25
4500 ~ 25
5000 ~ 25
5500 ~ 25
6000 ~ 25
6500 ~ 25
7000 ~ 25
7500 ~ ??
8000 ~ 25
9000 ~ 25

t*map Map
Screen 24

Idle ~ 00
25 ~ 05
20 ~ 04
15 ~ 03
10 ~ 02
05 ~ 00
00 ~ 00
2psi ~ 00
4psi ~ 00
6psi ~ 02
8psi ~ -04
10psi ~ -06
14psi ~ -10
16psi ~ -12
18 psi ~ -16
20 psi ~ -20

t*air Screen 25
Correction value Is expressed as number of degrees you wish to advance or Retard to the Ignition curve and values Is set at zero.

t*gap
Screen 26

0500 ~ 15
1000 ~ 15
1500 ~ 15
2000 ~ 14
2500 ~ 12
3000 ~ 10
3500 ~ 10
4000 ~ 10
4500 ~ 10
5000 ~ 10
5500 ~ 10
6000 ~ 10
6500 ~ 10
7000 ~ 10
8000 ~ 10

t*Inj Map
Screen 27

0500 ~ 120
1000 ~ 150
1500 ~ 150
2000 ~ 150
2500 ~ 150
3000 ~ 150
3500 ~ 150
4000 ~ 150
4500 ~ 180
5000 ~ 210
5500 ~ 210
6000 ~ 240
6500 ~ 240
7000 ~ 270
8000 ~ 270
9000 ~ 270

t*wat Map Screen 28


ANd the rest are zero

Option Map
Screen 30

Af_StE ~ 10
Dwell ~ 3.25 *set at Time Base - not at Duty Cycle*
REVstg ~ 1320
MAPstg ~ 02"
%stg ~ 50

Fuel pressure 40psi.

Let me know how it goes.

Get a video of the car after putting the map in, so if their is a problem can use the video to diagnose the problem.

hope that helps.

a_reyes1014

iTrader: (1)

thanks rx72c it almost starts but then the battery goes dead lol i got it running before but that was with 1000cc primary injectors and it was way too much fuel even with adjusting them

rx72c

iTrader: (8)

Try this idle map.

Idle Map
Screen 1

30" ~ 1.38
25" ~ 1.48
20" ~ 1.33
15" ~ 1.71
10" ~ 1.71
05" ~ 1.91
00" ~ 2.56
2-20psi ~ 4.95

jon4825

iTrader: (1)

Yesterday I went from my .65 bar spring in my wastegate to my 1 bar spring. I have a good base map, but can anyone estimate what numbers I should be running in my RPM wot map and Load map.. Right now I am all over the place because I tried increasing just my Load map and that resulted in not low enough a/f numbers and tons of hesitation and sputtering... I actualled raised those figures up into the 7's and 8's to bring my a/f down but it was not enough... I then increase my rpm_wot map extremely high
4500 -15
5000 -20
5500 -25
6000 -30
6500 -35
7000 -40
8000- 43

These brough my A/F's down but when I accelarate slowly, not under any real boost I can tell it is getting way to much gas....

So my question is, If I cant get my A/F's down by maxing out the load screen, while at the same time not having to put wot map figures to high so that they add to much fuel when accelerating slowly.. with little boost....what am i doing wrong...

After another 2 days of this I might just have to drop the 500 bucks for a professional dyno tune, but at the same time I reallyu want to learn how to do this...

Thanks,
A frustrated tuning newbie