New owner 1990 FC3S
#1
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Rialto Ca
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
New owner 1990 FC3S
Names David from the inland empire. Got myself a 90 fc3s NA for now.
Only mods done to it are a set of rims and a set of coils.
Rims are advan RG 1s
And a set of HKS hipermax Ds
So far everything's coming along well with it and I have some good plans for it.
Want to make it a daily that I could track if I wanted to.
Hope to boost it eventually get it caged and just little details here and there to set it off nice.
Hope to have you guys involved with my build along the way.
Only mods done to it are a set of rims and a set of coils.
Rims are advan RG 1s
And a set of HKS hipermax Ds
So far everything's coming along well with it and I have some good plans for it.
Want to make it a daily that I could track if I wanted to.
Hope to boost it eventually get it caged and just little details here and there to set it off nice.
Hope to have you guys involved with my build along the way.
Last edited by misterstyx69; 07-17-13 at 06:57 AM.
#4
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Rialto Ca
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
First issue with my FC!
Seems like my clutch master cylinder went out on me today.
I was in line waiting to get into a parking lot and all of a sudden I couldn't go into gear for ****.
Gunna replace it tomorrow and see if it solves my issue ha.
Seems like my clutch master cylinder went out on me today.
I was in line waiting to get into a parking lot and all of a sudden I couldn't go into gear for ****.
Gunna replace it tomorrow and see if it solves my issue ha.
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Rialto Ca
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
Changed my transmission out along with a throwout bearing and now it grinds when I try to go into gear.
Also my idle is bouncing when It never did before.
Anyone know what I could check for?
Also my idle is bouncing when It never did before.
Anyone know what I could check for?
#12
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Rialto Ca
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
#16
Junior Member
Join Date: Jun 2013
Location: Colorado Springs, CO
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
David, welcome to the forums.
I used to have an identical FC to yours and loved it. I actually blew the engine and had no clue about rotaries back then and sold it. Bad mistake... Have fun with that thing and don't let it go!
I used to have an identical FC to yours and loved it. I actually blew the engine and had no clue about rotaries back then and sold it. Bad mistake... Have fun with that thing and don't let it go!
#18
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Rialto Ca
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
Already having some issues with it haha.
My throwout bearing took a crap on me so I went and replaced it and when the tranny was out I thought it was a good time to replace it with another one I had that I thought was in better condition. Now I swapped everything back together and it grinds when I try to throw it into gear. Like the pressure plate isn't being disengaged enough. I bought a new master and slave cylinder also. Any ideas or what I could check for? Bad syncros?
It shifts fine when the car is off too.
My throwout bearing took a crap on me so I went and replaced it and when the tranny was out I thought it was a good time to replace it with another one I had that I thought was in better condition. Now I swapped everything back together and it grinds when I try to throw it into gear. Like the pressure plate isn't being disengaged enough. I bought a new master and slave cylinder also. Any ideas or what I could check for? Bad syncros?
It shifts fine when the car is off too.
Thread
Thread Starter
Forum
Replies
Last Post