What kind of shift knob to get?
#5
Full Member
Join Date: May 2001
Location: seattle, wa, usa
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
Momo all the way, here's a pick of mine. Hopefully this'll help you decide. The only downside if it even is a downside, is that you have to retighten the screws like once a month or so because if you wrench it around too hard it'll loosen just a tad, but even when its loose, you can still use it. In any case, good luck!
Peace,
AJ ^_^
Peace,
AJ ^_^
#6
Newb Photog
Join Date: Jul 2001
Location: new jersey
Posts: 2,171
Likes: 0
Received 0 Likes
on
0 Posts
**** doesn't fit in fd
i picked up my momo **** and it doesn't fit. i didn't like the fact that it was siiting so high so i cut the shifter down, to my surprise the shifter flared out dramaticaaly towards the tranny. do you think it would be okay if i shaved the sides alittle so that my momo **** can now fit. i still left enuff thread so the original shifter fits on.
luigi
94 fd
luigi
94 fd
#7
Full Member
Join Date: May 2001
Location: seattle, wa, usa
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
Hmm... I THOUGHT Momo ***** were universal but I guess not. I don't see why you couldn't trim the shaft down a little bit as long as in the end, there's enough thread left for the screws on the Momo **** to catch and grab onto. Well good luck!
Peace,
AJ ^_^
Peace,
AJ ^_^
Trending Topics
#9
Newb Photog
Join Date: Jul 2001
Location: new jersey
Posts: 2,171
Likes: 0
Received 0 Likes
on
0 Posts
Hmm... I THOUGHT Momo ***** were universal but I guess not. I don't see why you couldn't trim the shaft down a little bit as long as in the end, there's enough thread left for the screws on the Momo **** to catch and grab onto. Well good luck!
Peace,
AJ ^_^
aj my **** is the momo sphere and it doesn't use thread to hold on the shifter it grabs on with screws. hard to describe but it is very nice. i already cut the shifter down height wise, the stock **** feels better but i want to add the momo. because of the diameter of the bottom of the **** it doesn't fit around the bottom of the shifter, i want to make the shifter thinner. i don't forsee a problem because the height has been shorten, so it won't lose its strenght. what do you guys think?
Peace,
AJ ^_^
aj my **** is the momo sphere and it doesn't use thread to hold on the shifter it grabs on with screws. hard to describe but it is very nice. i already cut the shifter down height wise, the stock **** feels better but i want to add the momo. because of the diameter of the bottom of the **** it doesn't fit around the bottom of the shifter, i want to make the shifter thinner. i don't forsee a problem because the height has been shorten, so it won't lose its strenght. what do you guys think?
#10
Full Member
Join Date: May 2001
Location: seattle, wa, usa
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
I know what you're talkin about. It's all goods ^_-. I meant the three screws need the thread to catch onto for a firm grip on the shifter shaft. You shouldn't have any problems with cutting it shorter that I can foresee. Well good luck and I hope it comes out the way you want it to!
Peace,
AJ ^_^
Peace,
AJ ^_^
#12
Newb Photog
Join Date: Jul 2001
Location: new jersey
Posts: 2,171
Likes: 0
Received 0 Likes
on
0 Posts
i had this shift **** for months before i even brought the car. i payed $80 for this thing when it first came out, special ordered and everything, i like it to much to sell. i plan on putting a new transsission in next week so on the new one before installing i will do the modification outside of the car. hope it works.
luigi
94 fd
luigi
94 fd
Thread
Thread Starter
Forum
Replies
Last Post