Interior / Exterior / Audio Talk about interior and exterior mods including audio.

I have no sound

Thread Tools
 
Search this Thread
 
Old Jan 25, 2002 | 08:13 PM
  #1  
kemozabi's Avatar
Thread Starter
.....shhh hes coming.....
Tenured Member 05 Years
 
Joined: Dec 2001
Posts: 151
Likes: 0
From: Sacramento, CA
Exclamation I have no sound

I have no sound. my old deck was stolen out of my car but before that it all worked fine. but now after tryin to install another deck things arent goin the way they should. i have the antenna wired to the ground for now until i get my relay. That works, and the deck lights up but no sound comes out. i cant figure it out so someone plz help me. o ya and there are two wires that have nothin connected to them, they are both grey with a yellow stripe.
Reply
Old Jan 26, 2002 | 01:43 AM
  #2  
Icemark's Avatar
Former Moderator. RIP Icemark.
 
Joined: Apr 2001
Posts: 25,896
Likes: 24
From: Rohnert Park CA
what year or model?
Reply
Old Jan 26, 2002 | 02:12 PM
  #3  
kemozabi's Avatar
Thread Starter
.....shhh hes coming.....
Tenured Member 05 Years
 
Joined: Dec 2001
Posts: 151
Likes: 0
From: Sacramento, CA
86 n\a. it used to have the stock tape deck and the eq in it.
Reply
Old Jan 28, 2002 | 02:27 AM
  #4  
kemozabi's Avatar
Thread Starter
.....shhh hes coming.....
Tenured Member 05 Years
 
Joined: Dec 2001
Posts: 151
Likes: 0
From: Sacramento, CA
come on people work with me..........
Reply
Old Jan 28, 2002 | 10:36 AM
  #5  
Icemark's Avatar
Former Moderator. RIP Icemark.
 
Joined: Apr 2001
Posts: 25,896
Likes: 24
From: Rohnert Park CA
There are no grey/yellow there.

Perhaps you listed the wrong color???

Okay I'll post the radio wires again... Maybe somebody will do a search and find this next time.

LTBlue/Red= 12v+
LtBlue/White= +Accessory
LtBlue/Yellow= -power ant trigger
Red/Black=+ Lumination
White=Factory Amp Turn on

Ground to the body, use the 10mm bolt behind the center console front drivers access panel. Do not use the Red/Black as ground it will damage the interior light circuit and dimmer in the car

Front Speakers (maximum of a 15 watt peak from the radio):
LtGreen/Red= Left
LtGreen/Black= Left

LtGreen= Right
LtGreen/Yellow=Right

Rear Speakers (if applicable, if you have the amplified rear speakers again the Maximum of 15 watts peak is all the stock speaker amp input can handle):
Brown= Left rear
Brown/White= Left Rear

LtBlue= Right Rear
LtBlue/Orange=Right Rear
Reply
Old Jan 28, 2002 | 05:07 PM
  #6  
kemozabi's Avatar
Thread Starter
.....shhh hes coming.....
Tenured Member 05 Years
 
Joined: Dec 2001
Posts: 151
Likes: 0
From: Sacramento, CA
im pretty sure i have it all hooked up right.......but il give it another try before i shell out the bucks
Reply
Old Feb 2, 2002 | 09:11 PM
  #7  
RLBRX7's Avatar
Full Member
Tenured Member 05 Years
 
Joined: Nov 2001
Posts: 108
Likes: 0
From: Ohio
The wiring instructions above are correct. Some 1986 N/A's did not have any amplifiers under the speakers in the rear towers. If yours has none there will still be some wires with plugs on the end that would have gone into the amp. Don't use these wires for anything. The light blue series and the brown series are the wires to use for the rear speakers. These same wires must also be connected properly at the rear of the head unit.
Reply
Old Feb 3, 2002 | 02:44 AM
  #8  
kemozabi's Avatar
Thread Starter
.....shhh hes coming.....
Tenured Member 05 Years
 
Joined: Dec 2001
Posts: 151
Likes: 0
From: Sacramento, CA
ok.... let me try that out tomorrow, hopefully it will work. but shouldnt i have sound commin out the front speakers, or is there an amp there too that could be troublesome? thanks for the advice ima try it out
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Rbkouki
V-8 Powered RX-7's
0
Sep 29, 2015 08:54 PM
baix2
Power FC Forum
1
Sep 28, 2015 09:40 AM




All times are GMT -5. The time now is 09:10 AM.