Sgt. Pepper

I live close and am down for test fitting in an FC We can see how this works with the stock S5 mouse seatbelt...

f1spec

TTT thanx for al the people that came to our booth at HIN san francisco this past weekend ..

f1spec

TTT for the new week

DarkKnightFC

I would be interested in getting one if you could beat the Corbeau FX-1 price for seat and bracket. Which would be around $375 ish. The carbon is nice I'm just not into the whole carbon fiber deal because I would never see it unless I was looking in the hatch. \

Chris

audiobot7

so how much is this?

AzEKnightz

iTrader: (24)

I m in SF too, where is the shop located? I dont mind having my car for test fit =)

p.s. You can call me stupid, but whats a sponsored seller?

f1spec

kevlar coming soon

fritts

iTrader: (5)

I have corbeau A4's in my FD and they barely fit. I even removed the sliders. According to F1Spec's site their seats are wider and taller than the A4's so if you have an FD I have a hard time with thinking they'll fit. Has anyone even tried to yet?

ilike2eatricers

Haha the car featured in honda tuning with those seats is my buddy's car

chinaman

These are very nice looking seats. I'd very interested in the type 3 in carbon. Hopefully it's not too expensive.

f1spec

which type seat are you looking when you're refering to it won't fit. i know the type 3 will fit the fc

fritts

iTrader: (5)

I looked at both sets of dimensions you have listed on your site. Almost all of which are larger than the A4. The A4 just barely fits the FD and I would say not all that well. So I really doubt they would fit the FD the FC is another story.

Mahjik

iTrader: (1)

Yep, I mentioned this to him a while back:

https://www.rx7club.com/showpost.php...0&postcount=28

I would still be interested to hear about them actually test fitting each seat in a RX-7's (all gens if possible).

afterburn27

iTrader: (5)

The shoulder height is identical to a Sparco EVO and the shoulder width is actually slightly smaller (.5 cm). I have seen a few FD's with EVO's in them, granted they barely fit, but I think the TypeIII will be a close fit.

I bought one black typeIII in FRP and have it sitting next to me. It is a nice seat, quality is on par or better than the Corbeau FX-1 pro's I have sat in before. I don't have a lot of seat time in Sparco's or Recaro's so I can't comment there.

I will try and test fit the seat in the car this weekend if I have time. I am slammed with work and interviews recently, so we'll see. If it doesn't fit I have another use for it, so no biggie. I will not be using sliders, BTW.

DJ_Merle

iTrader: (6)

could I get a pm on pricing and shipment to Canada, thanks in advance.

Valkyrie

I still don't think we've got a straight answer about FIA ratings?

fritts

iTrader: (5)

I pm'd them about this and FIA rating is twice the cost of the regular seat.

Valkyrie

I'm curious as to why, personally...

I don't see how they could possibly make the seats any different since they're apparently buying them from a single factory in Asia, and if the price increase was because of testing required, I simply can't beleive that every seat would have to be tested invididually. That would be like crash-testing every car that is sold. Safety items are typically only intended to be used once before being replaced (or at least inspected)...

Or do just test seats until they get one that doesn't break, and sell it with an FIA sticker?

If they seats were that dissimilar in quality, I'm not sure how much confidence you could have in it's safety, even for the ones that passed any testing.

Unless it's just an insane markup based on the fact that people want FIA seats? You could get a Bride or a Recaro for that price.

afterburn27

iTrader: (5)

Well, looks like I wont get around to installing this seat for a while.

The front eccentric shaft/main pulley bolt backed out on the highway last night causing a huge mess and most likely destroying the thrust bearing and wahsers under the front cover. Maybe more damage to the internals depending on how much oil stayed in the engine for the short time it was running and spewing oil.

So I am having it towed back to a friend's place in Richmond while I finish up this semester at VT.

At least I can sit in my seat and pretend like I'm driving the FD.

fc3sfreek

iTrader: (6)

so is there an update about anything about this seat?

Tranquil

iTrader: (1)

I decided to order one of the Type II seats on sale for 250shipped with sliders and side mounts today.

I'll give a complete review on them and if they fit in my FB when they arrive. Then we'll know what's what.

EDIT: Hopefully if I like them enough, and write a comprehensive enough review I might be able to get a good deal so I can get a passenger seat.

f1spec

we have new in stock for the peoples who would like a better option for rails/sliders/brackets. we have the buddyclub super low downs that will fit all of our seats. and it only takes 15 mins to install.

SayNoToPistons

Whats there difference here?
http://f1spec.com/f1spectype2.html
http://f1spec.com/200131.html

theyre botht he same seats correct? fiberglass?

f1spec

they are both the same seat just different color. thats our type 2

Valkyrie

Well, how much are the rails?

Do you have them for the FC?

Also, how much is shipping on a single seat and rails? (assuming you leave out your free rails)

(ah nm, I remember it's 75 bucks... but that doesn't really seem reasonable)

I might be able to buy a seat in a few weeks.