Haltech i need a base map for an E6S
#1
so you got pistons oh wow
Thread Starter
iTrader: (1)
Join Date: Nov 2007
Location: Killeen, Texas
Posts: 900
Likes: 0
Received 0 Likes
on
0 Posts
i need a base map for an E6S
hey guys I was just hoping someone has a basemap or could tell me where to find one to at least start my car. It is for an 87 S4 TII. Im running the stock CAS and coils, 720/1600 low impedance Injectors, haltech 3 bar MAP Sensor and a haltech E6S.
i dont know if this other info is needed but the other mods I have are
LC-1 Wideband
Greddy Profec B Boost Controller
Turbonetics T-66 Dual Ball Bearing
FMIC with 2.5" piping
3" free flow Dual exhaust (no cats)
walbro 255 fuel pump
all Emisions Removed
Large street port, SCR 2mm Apex seals,new bearings, side seals and all springs
(engine was just rebuilt and has 0 hours of run time.)
42mm Wastegate
9mm spark plug wires
Aeromotive a1000 FPR with all steel braided -6 hoses
ACT Max extreme clutch
ACT street lite flywheel
I also have 2 MSD 6Al's but they are not installed yet. I could be missing other modifications but i dont think it would matter anyway. please let me know if I missed to add any important info so I can go ahead and add it up.
thanks in advance
i dont know if this other info is needed but the other mods I have are
LC-1 Wideband
Greddy Profec B Boost Controller
Turbonetics T-66 Dual Ball Bearing
FMIC with 2.5" piping
3" free flow Dual exhaust (no cats)
walbro 255 fuel pump
all Emisions Removed
Large street port, SCR 2mm Apex seals,new bearings, side seals and all springs
(engine was just rebuilt and has 0 hours of run time.)
42mm Wastegate
9mm spark plug wires
Aeromotive a1000 FPR with all steel braided -6 hoses
ACT Max extreme clutch
ACT street lite flywheel
I also have 2 MSD 6Al's but they are not installed yet. I could be missing other modifications but i dont think it would matter anyway. please let me know if I missed to add any important info so I can go ahead and add it up.
thanks in advance
#2
so you got pistons oh wow
Thread Starter
iTrader: (1)
Join Date: Nov 2007
Location: Killeen, Texas
Posts: 900
Likes: 0
Received 0 Likes
on
0 Posts
here is a link to a thread of the car in to see if it helps with the motivation and someone helps me out with the map!!!! Enjoy!
https://www.rx7club.com/2nd-generation-non-technical-pictures-198/some-pics-my-engine-bay-im-finally-almost-done-780487/
https://www.rx7club.com/2nd-generation-non-technical-pictures-198/some-pics-my-engine-bay-im-finally-almost-done-780487/
#3
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,844
Received 2,606 Likes
on
1,849 Posts
e6s = older than the internet! i suggest you look at an e6k map, and just start plugging stuff into your ecu. or just f-ing start tuning the thing.
#4
so you got pistons oh wow
Thread Starter
iTrader: (1)
Join Date: Nov 2007
Location: Killeen, Texas
Posts: 900
Likes: 0
Received 0 Likes
on
0 Posts
ok i loaded a map I have fuel but i have no spark whatsoever on any of the coils. Ive triple checked my wiring harness connections and coils conections and nothing seems to be wrong. it is reading 120 rpms on the laptop (without plugs). yes Im using the 2 MSD 8509's along with the wiring. Ive searched but no answers anywhere. please help!!!
Thread
Thread Starter
Forum
Replies
Last Post
killerrx710
Adaptronic Engine Mgmt - AUS
5
09-28-15 09:13 AM
killerrx710
2nd Generation Specific (1986-1992)
1
09-24-15 10:57 PM