Group Buy & Product Dev. FD RX-7 Post your possible Group Buys and product interest for the 1992 through 2002 FD series RX-7 in this section.

TNT Fuel Starve Eliminator for FD

Thread Tools
 
Search this Thread
 
Old 05-12-13, 03:20 PM
  #51  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
Originally Posted by tomsn16
Here's the evolution of the TNT design in the quest for a bullet proof FD fuel starve eliminator for really high g autoX and track use. .

1. We started with the stock tank and the purchased plastic tray ( baffle) cover hoping to reduce fuel load by 50 lbs...run with 1/4 tank. FAIL...still had to run 3/4 tank to prevent fuel starve.
2. Next we modified our stock tank to a half tank and retained the tray cover. FAIL..still had to run at 3/4 tank to prevent starve. Did achieve a significant weight reduction but we were still concerned about fuel starve on long high g sweepers.
3. We built a custom 5 gallon tank with a center baffle, used the stock pump assembly bulkhead and mounted our Bosch 044 outside the tank ( under the black plastic DS dust cover which puts it a bit below the tank ). To our amazement we still had fuel starve under 3/4 tank.
4. Finally we designed a 2 liter collector tank fed from the return line and a check valve hoping to keep 2 liters of fuel always available to the pickup. It worked. We start with 5 gallons and regularly run the tank down to 1-2 gallons. See pics.

The TNT is the same design adapted to the stock FD tank.
Holler with questions.
For those who may have missed it, above is the evolution of the TNT concept. The pics can be seen on page 1, post#7.
Old 05-12-13, 04:59 PM
  #52  
Money talks-mine says bye

iTrader: (18)
 
cone_crushr's Avatar
 
Join Date: May 2005
Location: LBC, CA
Posts: 718
Received 13 Likes on 10 Posts
My take on (A): the amount of fuel entering the check valve equals the fuel consumed by the engine (consumed = supply-return). As long as slosh never exposes the ball diameter to an air pocket, then the "sump-tank" remains full, even if the main tanks isn't. Once the ball orifice sees air though (during LH turns), that changes and the TNT level probably starts dropping.

Here's an example of why understanding the concept matters. I propose that the ball valve should be as close to the center of the tank as possible rather than near the edge as is currently designed. Admittedly you only gain ~3", but just curious why you chose the corner closest to the edge of the tank for the ball-valve location?

Originally Posted by tomsn16
snip...
2). We think the TNT tank stays almost full "most of the time" due to (A) the return is adding fuel when not at full throttle and (B) the check valve is pressure actuated and we believe the constant slosh forces create a net positive pressure that pushes fuel into the TNT over-and-above the average level of the main tank.

Someday we would like to figure out how to video the inside tank action but for now we believe our autoX car experience confirms that the TNT concept works.
Hope this makes since.
HPP
Old 05-12-13, 05:44 PM
  #53  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
"Here's an example of why understanding the concept matters. I propose that the ball valve should be as close to the center of the tank as possible rather than near the edge as is currently designed. Admittedly you only gain ~3", but just curious why you chose the corner closest to the edge of the tank for the ball-valve location?"

Thank you Cone Crushr.....excellent point and it is feasible to locate the CV in the center. It was there in an earlier design but changed when we were trying to fit a sock inside the TNT but that has now changed with the use of the Russel filter outside the TNT. We will seriously consider a center location.
Keep the feedback coming.
Old 05-12-13, 06:04 PM
  #54  
Money talks-mine says bye

iTrader: (18)
 
cone_crushr's Avatar
 
Join Date: May 2005
Location: LBC, CA
Posts: 718
Received 13 Likes on 10 Posts
I was unclear, I mean consider moving the ball-valve to the 'inboard' corner of your surge-tank (opposite side) so that it's as near as possible to the centerline of the car.
Old 05-12-13, 06:50 PM
  #55  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
Originally Posted by cone_crushr
I was unclear, I mean consider moving the ball-valve to the 'inboard' corner of your surge-tank (opposite side) so that it's as near as possible to the centerline of the car.
To be sure we are on the same page, here's a pic looking down into the main tank...pic right is the car drivers side.
Attached Thumbnails TNT Fuel Starve Eliminator for FD-100_1038.jpg  
Old 05-12-13, 07:22 PM
  #56  
Money talks-mine says bye

iTrader: (18)
 
cone_crushr's Avatar
 
Join Date: May 2005
Location: LBC, CA
Posts: 718
Received 13 Likes on 10 Posts
Yer right, I had inverted it in my head. Ball valve location looks good.
Old 05-12-13, 07:50 PM
  #57  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
Originally Posted by cone_crushr
Yer right, I had inverted it in my head. Ball valve location looks good.
Good deal....what would we do without pics.
One of our ongoing debates has been which is more important...centering the CV or the pick-up tube(s) in the TNT....but again as you pointed we are dealing with a couple of inches one way or the other (the TNT is 4" side-to-side). Likely no difference with the really important factor being having a CAPTIVE near 2 liters of fuel always available to the pump(s).
Old 05-13-13, 05:53 AM
  #58  
Rotary Enthusiast

iTrader: (9)
 
$lacker's Avatar
 
Join Date: Mar 2010
Location: Canada
Posts: 1,087
Received 15 Likes on 14 Posts
This is a great idea btw
Odd that stock fuel tanks don't all have a similar feature on sports cars
Old 05-13-13, 06:58 PM
  #59  
Eats, Sleeps, Dreams Rotary

iTrader: (10)
 
RCCAZ 1's Avatar
 
Join Date: Jun 2002
Location: Phoenix, AZ
Posts: 3,358
Received 76 Likes on 44 Posts
Put me down as interested Jim. Bosch 044.
Old 05-13-13, 06:59 PM
  #60  
Eats, Sleeps, Dreams Rotary

iTrader: (10)
 
RCCAZ 1's Avatar
 
Join Date: Jun 2002
Location: Phoenix, AZ
Posts: 3,358
Received 76 Likes on 44 Posts
^^Sorry... in tank please...
Old 05-13-13, 09:52 PM
  #61  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
Updated INTERESTED in GB LIST:

Feel free to edit as needed:

1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump
13. RCCAZ1......................Single Bosch 044 in tank

NOTE...".in-tank" tells us that your pump(s) is mounted on the OEM or CJM stalk as opposed to an external (outside the tank) mount. So far all on the
interested list have in-tank pumps.
Old 05-14-13, 02:28 PM
  #62  
Garage Hero

iTrader: (93)
 
mannykiller's Avatar
 
Join Date: Aug 2009
Location: Quartz Hill
Posts: 4,205
Likes: 0
Received 17 Likes on 14 Posts
1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump
13. RCCAZ1......................Single Bosch 044 in tank
Old 05-15-13, 07:42 AM
  #63  
Rotary Enthusiast

iTrader: (9)
 
$lacker's Avatar
 
Join Date: Mar 2010
Location: Canada
Posts: 1,087
Received 15 Likes on 14 Posts
1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
Old 05-24-13, 02:45 PM
  #64  
Rotary Enthusiast

iTrader: (9)
 
$lacker's Avatar
 
Join Date: Mar 2010
Location: Canada
Posts: 1,087
Received 15 Likes on 14 Posts
Good idea to make the top of the metal container removable btw
If it were permanently fixed you wouldn't be able to clean/inspect the inside
Old 05-28-13, 02:33 PM
  #65  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
Originally Posted by $lacker
Good idea to make the top of the metal container removable btw
If it were permanently fixed you wouldn't be able to clean/inspect the inside
Yep, the top is removable for maintenance and initial install of the check valve and the suction line fittings.
Progress report......our welder has been jammed for the past two weeks so finishing the first two units( one single pump the other dual) has been delayed to next week.Will keep you posted.
Old 06-06-13, 06:47 PM
  #66  
Rotary Enthusiast

iTrader: (9)
 
$lacker's Avatar
 
Join Date: Mar 2010
Location: Canada
Posts: 1,087
Received 15 Likes on 14 Posts
Still planning to start the GB in June?
Old 06-06-13, 07:37 PM
  #67  
Junior Member

 
poop2003's Avatar
 
Join Date: Dec 2005
Location: Australia
Posts: 42
Likes: 0
Received 0 Likes on 0 Posts
Interested

1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
14. Poop2003.....................Single Sard 280L in tank
Old 06-07-13, 12:37 AM
  #68  
STA
Junior Member
 
STA's Avatar
 
Join Date: Aug 2012
Location: Finland
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Also really interested in this.

Walbro E85 400lph pump (aka 485), installed inside tank.
Old 06-07-13, 02:59 AM
  #69  
Senior Member

iTrader: (4)
 
SpAm@FC's Avatar
 
Join Date: Jun 2003
Location: Austria
Posts: 734
Likes: 0
Received 1 Like on 1 Post
Interested

1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
14. Poop2003.....................Single Sard 280L in tank
15. SpAm@FC.....................CJM dual Bosch 044's In-tank

I'm in for CJM dual Bosch Make this happen, that's looking like a very nice product! Would be great not to have to mount a surgetank with lines inside the cabin
Old 06-07-13, 03:29 PM
  #70  
Eats, Sleeps, Dreams Rotary

Thread Starter
iTrader: (283)
 
tomsn16's Avatar
 
Join Date: Mar 2009
Location: Murfreesboro TN
Posts: 4,209
Received 499 Likes on 332 Posts
I'm in for CJM dual Bosch Make this happen, that's looking like a very nice product! Would be great not to have to mount a surgetank with lines inside the cabin

This product will happen. Have had delays with our ace welder (very busy) but should have two test units made next week...one single,one dual. The dual pump unit will be tested by a nearby FD drag racer (very very fast car) and if the TNT satisfies this application we will start making both dual and single units as fast as we can.
Will keep you posted weekly.
HPP
Old 06-09-13, 09:07 AM
  #71  
Rotary Enthusiast

iTrader: (26)
 
Sandrock's Avatar
 
Join Date: Mar 2009
Location: Clayton NC
Posts: 1,071
Received 0 Likes on 0 Posts
Interested

1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
14. Poop2003.....................Single Sard 280L in tank
15. SpAm@FC.....................CJM dual Bosch 044's In-tank
16. Sandrock .......................Single bosch 044 in tank.

I'm in for CJM dual Bosch Make this happen, that's looking like a very nice product! Would be great not to have to mount a surgetank with lines inside the cabin [/QUOTE]
Old 06-09-13, 09:08 AM
  #72  
Rotary Enthusiast

iTrader: (26)
 
Sandrock's Avatar
 
Join Date: Mar 2009
Location: Clayton NC
Posts: 1,071
Received 0 Likes on 0 Posts
^^^ Forgot to take the rest of the persons comment out..
Old 06-11-13, 02:20 AM
  #73  
Senior Member

iTrader: (49)
 
perf0rmance's Avatar
 
Join Date: May 2011
Location: Bay Area -> California
Posts: 338
Likes: 0
Received 0 Likes on 0 Posts
Interested

1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
14. Poop2003.....................Single Sard 280L in tank
15. SpAm@FC.....................CJM dual Bosch 044's In-tank
16. Sandrock .......................Single bosch 044 in tank.
17. perf0rmance .................Single Supra in tank (can switch to bosch 044 if preferred)
Old 06-11-13, 02:12 PM
  #74  
JBF
Senior Member
iTrader: (13)
 
JBF's Avatar
 
Join Date: Apr 2011
Location: Willow Springs, CA
Posts: 605
Likes: 0
Received 2 Likes on 2 Posts
1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
14. Poop2003.....................Single Sard 280L in tank
15. SpAm@FC.....................CJM dual Bosch 044's In-tank
16. Sandrock .......................Single bosch 044 in tank.
17. perf0rmance .................Single Supra in tank (can switch to bosch 044 if preferred)
18. JBF...............................Single Aeromotive 340 in tank
Old 06-12-13, 07:11 AM
  #75  
STA
Junior Member
 
STA's Avatar
 
Join Date: Aug 2012
Location: Finland
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
1. AzEKnightz...............CJM dual Walbro 255's(not ready now but later)
2. Smokey The Talon.......in-tank
3. FC3S1991..................CJM dual Walbro
4. Genzer.......................Rotary Performance pump
5.SK8WORLD...................Dual Supra pumps in-tank
6. R-R-RX7......................Single Bosch 044 intank
7. ROVERS.....................Single supra pump intank
8. Grinch........................ Single Walbro 485
9. Mannykiller.................CJM dual Bosch 044's In-tank
10. Chon........................pump in-tank
11.Vrx8............................Dual Aeromotive 340 (depends on drag results)
12. $lacker ..................... RP Competition Fuel Pump in-tank
13. RCCAZ1......................Single Bosch 044 in tank
14. Poop2003.....................Single Sard 280L in tank
15. SpAm@FC.....................CJM dual Bosch 044's In-tank
16. Sandrock .......................Single bosch 044 in tank.
17. perf0rmance .................Single Supra in tank (can switch to bosch 044 if preferred)
18. JBF...............................Single Aeromotive 340 in tank
19. STA..............................Single Walbro 485


Quick Reply: TNT Fuel Starve Eliminator for FD



All times are GMT -5. The time now is 09:45 AM.