RX7Club.com - Mazda RX7 Forum
Having to cut off the bolts to get them out, this part really sucked
Having to cut off the bolts to get them out, this part really sucked
0 2015/05/23 08:45:01
Having to cut off the bolts to get them out, this part really sucked
Having to cut off the bolts to get them out, this part really sucked
0 2015/05/23 08:44:40
Carnage of tearing apart a rusty old axle
Carnage of tearing apart a rusty old axle
0 2015/05/23 08:44:18
Carnage of tearing apart a rusty old axle
Carnage of tearing apart a rusty old axle
0 2015/05/23 08:44:00
The metal in the bushings all welded to the bolts through them, so I had to cut each bolt at least twice to get it removed from the axle carrier - annoying!
The metal in the bushings all welded to the bolts through them, so I had to cut each bolt at least twice to get it removed from the axle carrier - annoying!
0 2015/05/22 21:01:13
After getting the first axle out, had to cut the brake line there since it was so rusted into the soft line union.
After getting the first axle out, had to cut the brake line there since it was so rusted into the soft line union.
0 2015/05/22 21:00:51
SE axles are finally free from their carrier!
SE axles are finally free from their carrier!
0 2015/05/22 21:00:35
Made my own OMP block off plate with some flat steel and shears - came out pretty well! Sealed it up with some Black RTV and she'll be good!
Made my own OMP block off plate with some flat steel and shears - came out pretty well! Sealed it up with some Black RTV and she'll be good!
0 2015/05/22 21:00:13
Axle seal and wheel bearings are the right size, always a good day when you don't have to order more parts
Axle seal and wheel bearings are the right size, always a good day when you don't have to order more parts
0 2015/05/22 20:59:53
Going to have to cut these buggers off, should be entertaining to say the least
Going to have to cut these buggers off, should be entertaining to say the least
0 2015/05/22 20:59:33
C1M090 is stamped on the pinion and ring gears of the LSD rear differnetial
C1M090 is stamped on the pinion and ring gears of the LSD rear differnetial
0 2015/05/22 20:59:22
C1M090 is stamped on the pinion gear of the LSD rear differnetial
C1M090 is stamped on the pinion gear of the LSD rear differnetial
0 2015/05/22 20:59:00
C1M090 is stamped on the ring gear of the LSD rear differnetial
C1M090 is stamped on the ring gear of the LSD rear differnetial
0 2015/05/22 20:58:53
0 2015/05/20 21:15:51
0 2015/05/20 21:04:36
0 2015/05/20 21:04:25
GSL-SE full suspension setup removed from the parts car. I used to dream of owning a full set of these, I'm so glad that I finally do!
GSL-SE full suspension setup removed from the parts car. I used to dream of owning a full set of these, I'm so glad that I finally do!
0 2015/05/20 20:53:10
Stock suspension bolt collection for the FB with new lock nuts and flat washers in place of the standard hex nuts and lock washers. This should help eliminate binding in the suspension components since there won't be as much pressure pinching the mounts together on the bushings.
Stock suspension bolt collection for the FB with new lock nuts and flat washers in place of the standard hex nuts and lock washers. This should help eliminate binding in the suspension components since there won't be as much pressure pinching the mounts together on the bushings.
0 2015/05/20 20:52:55
Corrosion on the center iron, it's porous like a sponge from where coolant must have sat and ate through the nitride coating and rusted the metal away. Time for a new center iron I guess!
Corrosion on the center iron, it's porous like a sponge from where coolant must have sat and ate through the nitride coating and rusted the metal away. Time for a new center iron I guess!
0 2015/05/20 20:52:33
Corrosion on the center iron, it's porous like a sponge from where coolant must have sat and ate through the nitride coating and rusted the metal away. Time for a new center iron I guess!
Corrosion on the center iron, it's porous like a sponge from where coolant must have sat and ate through the nitride coating and rusted the metal away. Time for a new center iron I guess!
0 2015/05/20 20:52:24
Oil Pressure Regulator before hammer treatment - went from ~8.1mm to ~6.1mm diameter hole which should raise the oil pressure
Oil Pressure Regulator before hammer treatment - went from ~8.1mm to ~6.1mm diameter hole which should raise the oil pressure
0 2015/05/20 20:52:16
Oil Pressure Regulator after hammer treatment - went from ~8.1mm to ~6.1mm diameter hole which should raise the oil pressure
Oil Pressure Regulator after hammer treatment - went from ~8.1mm to ~6.1mm diameter hole which should raise the oil pressure
0 2015/05/20 20:52:00
Engine cleaned with a toothbrush-sized wire brush to double check all the components
Engine cleaned with a toothbrush-sized wire brush to double check all the components
0 2015/05/20 20:51:42
FB rear axle control arms and Watts linkage all painted and cleaned up
FB rear axle control arms and Watts linkage all painted and cleaned up
0 2015/05/20 20:51:22
FB rear axle control arms and Watts linkage getting ready for new bushings
FB rear axle control arms and Watts linkage getting ready for new bushings
0 2015/05/20 20:51:02
FB rear axle control arms and Watts linkage with new Energy Suspension graphite-impregnated polyurethane bushings
FB rear axle control arms and Watts linkage with new Energy Suspension graphite-impregnated polyurethane bushings
0 2015/05/20 20:50:39
Epsilon 3-piece 16" staggered Center Lock wheels 16in three piece
Epsilon 3-piece 16" staggered Center Lock wheels 16in three piece
0 2015/05/20 20:50:17
Epsilon 3-piece 16" staggered Center Lock wheels 16in three piece
Epsilon 3-piece 16" staggered Center Lock wheels 16in three piece
0 2015/05/20 20:49:36
Stock suspension bolt collection for the FB
Stock suspension bolt collection for the FB
0 2015/05/20 20:49:21
Dad and grandpa helping strap down the car on the way to the scrapper
Dad and grandpa helping strap down the car on the way to the scrapper
0 2015/05/18 18:05:22
4x4 status, trying to get the rear axle out
4x4 status, trying to get the rear axle out
0 2015/05/18 18:04:57
Examining and evaluating how to get the rear axle out somewhat safely
Examining and evaluating how to get the rear axle out somewhat safely
0 2015/05/18 18:04:50
Back of Turn Light
Back of Turn Light
0 2012/01/25 15:41:06
Turn Light Without Cover
Turn Light Without Cover
0 2012/01/25 15:41:06
Turn Light
Turn Light
0 2012/01/25 15:41:06
Tail Light Back of Light Connector
Tail Light Back of Light Connector
0 2012/01/25 15:31:04
Tail Light Turn Light
Tail Light Turn Light
0 2012/01/25 15:31:04
Tail Light Brake Tail Bulb Connection
Tail Light Brake Tail Bulb Connection
0 2012/01/25 15:27:43
Tail Light Connector and Brake Tail Bulbs
Tail Light Connector and Brake Tail Bulbs
0 2012/01/25 15:27:43
Tail Light Connector
Tail Light Connector
0 2012/01/25 15:22:09