RX7Club.com - Mazda RX7 Forum
getting nice center punch started as close to center as possible
getting nice center punch started as close to center as possible
0 2010/12/04 21:39:48
heat it till it is smoking hot
heat it till it is smoking hot
0 2010/12/04 21:39:48
hole is drilled just needs lots of heat now
hole is drilled just needs lots of heat now
0 2010/12/04 21:37:46
broken thermostat housing bolt
broken thermostat housing bolt
0 2010/12/04 21:37:46
Time to re group
Time to re group
0 2010/12/04 21:37:46
I cant believe how rough the center iron intake was
I cant believe how rough the center iron intake was
0 2010/12/04 21:34:37
up1
up1
0 2010/12/04 21:34:37
taking the ridge from inside the stock lower intake
taking the ridge from inside the stock lower intake
0 2010/12/04 21:32:17
new bike 024
new bike 024
0 2010/12/04 21:32:17
cleaning out all the rough from inside the intake
cleaning out all the rough from inside the intake
0 2010/12/04 21:32:17
alcohol 850 double pump with mechanical secondaries brand-new never used . not for my project
alcohol 850 double pump with mechanical secondaries brand-new never used . not for my project
0 2010/12/03 20:09:46
500 holley race carb for 13b drag bike ready for cleaning and rebuild
500 holley race carb for 13b drag bike ready for cleaning and rebuild
0 2010/12/03 20:09:46
alcohol 850 double pump with mechanical choke-less intended for 750 horse mustang ..This thing is amazing it has 95 jets in both sides plus each jet chamber is drilled to 100 thou. (no it's not for the 13b,), making a total of 780 thou. it needs two separate lines to feed the bitch you guys talk mileage she is use to get about 6 gals of alcohol mix per quarter mile
alcohol 850 double pump with mechanical choke-less intended for 750 horse mustang ..This thing is amazing it has 95 jets in both sides plus each jet chamber is drilled to 100 thou. (no it's not for the 13b,), making a total of 780 thou. it needs two separate lines to feed the bitch you guys talk mileage she is use to get about 6 gals of alcohol mix per quarter mile
0 2010/12/03 20:09:46
Intake cleanout coming along
Intake cleanout coming along
0 2010/12/01 08:58:50
Just starting to clean out inside of intake
Just starting to clean out inside of intake
0 2010/12/01 08:58:50
Stock lower intake
Stock lower intake
0 2010/12/01 08:58:50
Pin in the port valve was wore out flush with the inside and just rocked back and forth in the hole on one side .. Don't know how it never got sucked in
Pin in the port valve was wore out flush with the inside and just rocked back and forth in the hole on one side .. Don't know how it never got sucked in
0 2010/12/01 08:47:33
13b Just removed from 86 rx7
13b Just removed from 86 rx7
0 2010/12/01 08:47:33
cleaning up
cleaning up
0 2010/11/30 19:45:04
fresh out off engine compartment
fresh out off engine compartment
0 2010/11/30 19:45:04
Getting port actuators working proper once cleaned up and re sealed I am very surprised how smooth they work with good shafts and seals .. In stead of buying new seals for the actuator shafts I used a wick seal product that I use when I rebuild large irrigation pumps It is just a heat resistant wick with graphite in it for lubrication , I just pack it into the seal cavity around and around until it is full with the shaft installed .. once the packing is all tight and in place the shaft can be removed and the clips and screw caps put in place and reinstalled .. If it is packed in tight around the shaft no it will not leak air
Getting port actuators working proper once cleaned up and re sealed I am very surprised how smooth they work with good shafts and seals .. In stead of buying new seals for the actuator shafts I used a wick seal product that I use when I rebuild large irrigation pumps It is just a heat resistant wick with graphite in it for lubrication , I just pack it into the seal cavity around and around until it is full with the shaft installed .. once the packing is all tight and in place the shaft can be removed and the clips and screw caps put in place and reinstalled .. If it is packed in tight around the shaft no it will not leak air
0 2010/11/30 15:10:55
Getting the 13b cleaned up a bit .. and ready for the home made air box.. took a large amount of aluminum form inside the lower stock intake
Getting the 13b cleaned up a bit .. and ready for the home made air box.. took a large amount of aluminum form inside the lower stock intake
2 2010/11/30 15:10:55