I am looking for some nice detail pics of an FC engine bay with basically everything removed that isnt needed with a haltech and fmic. I need something to go by that looks good.

Thanks
-Morbius

 

I got some nice pics of my engine bay at home if you want me to post them later. I will need someone to host them for me if you want some big clear pics.

 

You can email them to me at bmallow@matw.com and ill post them up no biggie. I am just getting ready to tear down and strip everything else for the haltech and to4e install. Figure I would see what im shooting for.

-Morbius

 

I'll send you some pics around say 4:30 when I get home.

 

 

god damn thats so much time and money in that car its rediculous

 

All that time and money and it still looks like hes running stock fuel injection.

 

Vaughnc,

Other than looking badass you seem to have left alot of stuff on that engine. Any pics of one without AC, PS and all the other fluff

Thanks
-Morbius

 

pssst...
Thats not his car Its just a pic he saved, probly done by border.

 

Yo,


I'm waiting to see 1FastT2's engine bay pic again. *drool*

Here's the thread w/the pics.

https://www.rx7club.com/forum/showth...threadid=68828

KS
1989 GTUs "I wanna buy it!"

 

The pics have been sent, post em up when you get a chance.

 

From:http://www.cabrio7.org/mods/

 

Thanks for the pics 1FastT2 thats almost exactly what I was looking for. Here they are for everyone else to see...













Thanks Again
-Morbius

 

1FastT2, what kind of Hp you runnin? My god, that is super sexy!!! Wow, there isn't words to describe that engine bay......

 

Morbius: If there is anything you would like a pic of just let me know. Thanks for posting them. I had my car dynoed when I was running only 8psi with 270rwhp. I since turned up the boost to about 12psi and there is a huge difference. No dyno #s though.

 

MY GOD!!! You have like 325ish hp don't you!! That would be super fun!!! Man, get us some dyno sheets and videos!!!

 

1FastT2,

That setup is pretty much what I was looking for. Mine want be as pretty im sure but hell I will leave the hood closed as long as its functional. Do you have a mod list so I can see how close the setup im shooting for is. Hell I havent driven my T2 in over a year so im sorta excited to get it back on the road finally.

Thanks
-Morbius

 

Heres the list thus far.

Engine Internals:

-Big street port, intake/exhaust
-Racing Beat hardened stationary gears
-3rd Gen. Corner seal springs
-Racing Beat 85psi oil pressure reg.
-All other internals are new stock parts.

Engine Externals:

-Racing Beat main/alternator pulley
-Racing Beat oil pressure/temp adaptor
-Greddy V-spec FMIC

Turbo System:

-TO4B 60-1 P-trim 0.84 Exhaust housing
-XS Engineering divided manifold
-HKS SS BOV
-HKS standard 40mm wastegate
-manual boost controller

Engine Management:

-Haltech E6K

Ignition System:

-stock coils
-8.8mm Magnacore plug wires
-NGK stock plug ratings for now

Mics Stuff:

-ACT 6 puck clutch
-Brand new tranny from Mazda
-Perma-cool electric fan
-Throttle body mod.
-full 3” exhaust from turbo back
-Apexi Dual N1 cat back system
-Optima red top battery

Im sure there is more but this is the major stuff.

 

I need to print out your mods for my X-Mas list this year

 

I can sell you the car for a good package deal.

 

How much did the new tranny run you?

Your car looks great, but I told you that before.

 

Well the tranny cost the guy $2,300 from the dealer. I bought it with 60 miles on it for i think it was something like $800, it was so cheap I couldn't pass up the deal.

 

That's a great deal for a tranny! I am expecting to pay $250 or so for one with 75K+ miles.

 

HAHAHA, I ran into that deal by luck and jumped on it as soon as I seen it.