The OFFICIAL post pics of your Drift Car thread:
#3884
God, I wish. If I had the dough I would oblige.
1uz ftw. 92 LS=(thicker rods+boost). Haven't decided whether boost is in the budget yet. Got to do something about the weak sauce w58 first. Anybody got some 550 injectors laying around? I need 8 of them on the cheap.
LS1>1uz all day.
1uz ftw. 92 LS=(thicker rods+boost). Haven't decided whether boost is in the budget yet. Got to do something about the weak sauce w58 first. Anybody got some 550 injectors laying around? I need 8 of them on the cheap.
LS1>1uz all day.
#3888
Drift Ready FC
Its to bad I had a pretty messed up failure at Balcony yesterday otherwise Id have some new pics to post. I managed to shear in half a brand new diff stub shaft in about 10 mins while doing a figure 8. Tomarrow I begin trying to fish out the half inch tip of the shaft.
#3890
Garage Life
iTrader: (8)
I love the strong stance it puts out with 255s ! 17x9 +15 fn01s with 50mm spacer and -.5 camber 50mm wide rear fenders
KA-t?? Im building one too for a dd. I just finished a KA-t setup 3 months ago on my gfs s14 and its running strong! Stock KA24de, rebuilt head, new head gasket,new intake gaskets, bottom mount manifold, s15 t28 bb turbo, 370cc injectors, safc, boosting just 5psi until she gets her Nistune. So far its smoking all the other guys with sr20 loll KA-t FTW!
#3892
I break Diff mounts
iTrader: (1)
I love the strong stance it puts out with 255s ! 17x9 +15 fn01s with 50mm spacer and -.5 camber 50mm wide rear fenders
KA-t?? Im building one too for a dd. I just finished a KA-t setup 3 months ago on my gfs s14 and its running strong! Stock KA24de, rebuilt head, new head gasket,new intake gaskets, bottom mount manifold, s15 t28 bb turbo, 370cc injectors, safc, boosting just 5psi until she gets her Nistune. So far its smoking all the other guys with sr20 loll KA-t FTW!
Single Cam
KA24e
Arias 8.8 pistons
Eagle rods
ARP head studs
ARP main studs
Blitz KKK K26/k27 turbo
need to get a fuel setup going soon. Using Moates Ostrich 2.0 for ecu control
Gotta send block off to get bored and honed.
#3894
Full Member
Join Date: Jan 2010
Location: philadelphia
Posts: 163
Likes: 0
Received 0 Likes
on
0 Posts
#3898
I break Diff mounts
iTrader: (1)
^that's why I'm probably putting in a Z33 tranny.
My friend(LS1 FC George) is making SR->z33 adapters and is working on KA ->Z33 adapters.
I'll lose my speedo unless I fab something up but the driveline should be good for the 300-400rw I expect to push.
You have to mill the bell housing down and cut length off the shifter section.
Here's a side by side of SR vs Z33 tranny
My friend(LS1 FC George) is making SR->z33 adapters and is working on KA ->Z33 adapters.
I'll lose my speedo unless I fab something up but the driveline should be good for the 300-400rw I expect to push.
You have to mill the bell housing down and cut length off the shifter section.
Here's a side by side of SR vs Z33 tranny