Canadian Forum Canadian users, post event and club info here.

Apparently rotaries are prohibited...

Thread Tools
 
Search this Thread
 
Old Sep 16, 2012 | 12:19 AM
  #1  
cBigganz's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Oct 2011
Posts: 98
Likes: 1
From: Kelowna, BC
BC Apparently rotaries are prohibited...

Just found a neat little excerpt in the BC motor vehicle act, be careful where you decelerate...

Noise increase or flames prohibited
(5) No person shall drive or operate a motor vehicle propelled by an internal combustion engine equipped with a muffler or exhaust system to which is attached any device which increases the noise of the expulsion of the gases from the engine or allows a flame to be emitted from the exhaust system.

Motor Vehicle Act Regulations
Noticed this while looking for regulations related to bending a license plate. None exist for that as far as I can tell.
Reply
Old Sep 16, 2012 | 01:09 AM
  #2  
misterstyx69's Avatar
Retired Moderator, RIP
Tenured Member: 20 Years
iTrader: (142)
 
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
.......................................
Noise increase or flames prohibited Unless lighting Farts at night.
(5) No person shall drive a Freakin Honda or operate a Rx7 Based vehicle propelled by an internal combustion engine equipped with a muffler or exhaust system to which is attached any device which increases the noise of the expulsion of the gases from the engine or allows a flame to be emitted from the exhaust system.Unless you own a pink Drag Car,then it's OK.

Motor Vehicle Act Regulations
.........................................
There: I amended it..lol!
Reply
Old Sep 16, 2012 | 02:07 AM
  #3  
cBigganz's Avatar
Thread Starter
Full Member
Tenured Member 05 Years
 
Joined: Oct 2011
Posts: 98
Likes: 1
From: Kelowna, BC
Now to let my car fade to a lighter shade of pink.
Reply
Old Sep 16, 2012 | 12:23 PM
  #4  
djphonics's Avatar
Senior Member
Tenured Member: 15 Years
iTrader: (1)
 
Joined: Sep 2006
Posts: 701
Likes: 0
From: Oakville Ontario Canada
What that says to me is that you can not add any additional hardware to your exhaust to increase it's noise, or emit flames. meaning that you can't have a butterfly valve to increase or decrease noise or a spark plug at the end of tail pipe. That's interesting as many of the newer sports cars make use of butterfly valves in their exhaust systems.
Reply
Old Sep 17, 2012 | 01:08 AM
  #5  
rx7racerca's Avatar
Rotary Freak
Tenured Member: 20 Years
Liked
iTrader: (1)
 
Joined: Jul 2004
Posts: 1,725
Likes: 8
From: Lake Country, BC, Canada
Bent plate will be covered in whatever section of your statutes governs the display of the plate - in Alberta, it's considered tampering with the plate, same as if you painted different numbers on it, or just painted over it - and it's mucho dinero.

The other rule deals with devices that add and ignite gas in the exhaust - although I'm sure they could apply it to a modded rotary; with the required cats, there shouldn't be flames at the exhaust anyway. So one way or another, if you're shooting flames on the street, they can nail you for something.
Reply
Old Sep 17, 2012 | 02:42 AM
  #6  
hioctane-dtc's Avatar
Full Member
Tenured Member 10 Years
iTrader: (1)
 
Joined: Jul 2009
Posts: 173
Likes: 0
From: Vancouver, BC
This is very interesting.... oh well, better to know than getting pulled over not knowing what you did wrong.
Reply
Old Sep 17, 2012 | 04:22 AM
  #7  
Chad D.'s Avatar
Rotary Enthusiast
iTrader: (2)
 
Joined: Dec 2009
Posts: 192
Likes: 0
From: South of Detroit
I've received an "improper muffler" ticket in Ontario for flames.
Reply
Old Sep 17, 2012 | 07:59 AM
  #8  
MazdaMike02's Avatar
Mazda Tech
iTrader: (4)
 
Joined: Nov 2007
Posts: 1,589
Likes: 1
From: Tottenham, ON
Really easy to fight as long as the sound is within the acceptable decible range. All you gotta do is say the exhaust outlet is level with the bumper and the exhaust gasses properly exit behind the vehicle. As long as its not too loud, that ticket is BS.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
datfast1
Old School and Other Rotary
18
Jun 20, 2019 10:53 PM
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
Under PSI
3rd Generation Specific (1993-2002)
19
Sep 23, 2015 11:47 PM
ZacMan
Build Threads
4
Sep 19, 2015 09:20 PM
datfast1
West RX-7 Forum
3
Sep 14, 2015 06:58 PM




All times are GMT -5. The time now is 02:52 PM.