ahh ok
well whats the quest for now? LS' are in the 300 hp range are they not? Getting another 100 out've it should be easy, with minor things like the cam you mentioned, headers, and tune. I am no help on a cam, there are so many cam options for all v8s its mind boggling, and headache worthy |
|
Originally Posted by Fuhnortoner
(Post 12177016)
Why is the ronin kit bette? Whats the difference? Do they offer a drive shaft?
Just gonna nos it and go, maybe a cam. Any recommendations for a cam? With Granny's your exhaust needs to go over the trans cross member. C4 Corvette aluminium driveshafts work with the correct rear flange swapped on. Or Granny's driveshaft. Orders Granny's swaybar relocation brackets, and Stu Kelly Motorsports clutch master cylinder bracket. As far as a cam, yea there are many that will get you to around 400 WHP with what you have. You'll need to upgrade the valvesprings at a minimum for any cam. You'll need bigger injectors to make the 400 WHP. As far as a recommendation, do you value nicer street and low RPM manners? I'm a big fan of the ASA cam, I have one in my car and it made 401/401 to the tire. It has got a lot of overlap so it sounds pretty mean. Low RPM manners are not the best but it is pretty street able. It has relatively low lift ,which is easy on the valve train, and it has a wide powerband. My car makes over 350 ft.lbs. of torque form 3500 RPM to 6700 RPM. There are many other cams that will get you there, some with a slightly narrower powerband, that have better street manners, some with more aggressive lift, lots of options. With an otherwise stock motor you don't want to get too aggressive, but 400 WHP or close is doable with a good exhaust and intake. |
Hmmm. Maybe ill just leave her stock and run the nitrous kit for now. Have some pondering to do.
BTW im running the 4l60e for now, so i think theres no need for the clutch master cylinder kit as of yet. |
What is the ECU/Engine out of? Is it not a candidate for using HP Tuners?
|
Originally Posted by Lavitzlegend
(Post 12177273)
What is the ECU/Engine out of? Is it not a candidate for using HP Tuners?
|
OK so i think i have some things figured out.
1. Cam: 224 112 +4 good streetable cam with flat torque curve, and a lil lopey. +50rwhp??? 2. I know i need valve springs. Not sure which ones to get or what the differences are. I'm thinking comp 918s, but thats just from what i read on other people's setups. 3. Short header with catless X straight pipe. Cold air intake. Port TB. +20rwhp 4. NX Plate wet kit, 100 shot. So that puts me close to 390-400whp without the squeeze. Should i be fine with the stock injectors? Because i really dont wanna spend more money. |
Oh yeah and this came. My birthday was 2 months ago.
https://cimg3.ibsrv.net/gimg/www.rx7...e7ca861d5f.jpg |
Plan:
strap NOS to an LS pullout Godspeed, sir. |
Originally Posted by Narfle
(Post 12177735)
Plan:
strap NOS to an LS pullout Godspeed, sir. |
1 Attachment(s)
Originally Posted by Fuhnortoner
(Post 12177761)
What was I thinking?!?!
"Hey! Watch this!" "What could possibly go wrong?" "I got this." In for rod knock. Attachment 603943 |
Haters gonna hate. Keep workin on that interior bud!:icon_tup:
|
Well engine made it in one piece!
On top of the Nitrous kit I purchased a Comp cam, 223/230 .585/.600 111+1, should give me a nice lopey idle to make all the girls panties wet. But really, has a supposed flat torque curve, super easy to drive even with the lopey idle. Springs on the way as well. Expecting 350whp Purchased an engine install plate that bolts to the intake manifold area. this thing was a bitch to get off the trailer using the tranny bolts. Picked up a new soldering tip for my Weller, some shrink tube, and 200 feet of 18ga wire to start the harness rebuild/reroute. Still waiting on my granny kit. Those guys dont like to answer the phone after they have your money. Ive been working so much lately i havent had time to do shit. Think im off this weekend. Cant wait to start working on this thing https://cimg2.ibsrv.net/gimg/www.rx7...2c6f6d0dcf.jpg |
Finally found some free time over the holiday to put in some work on this bad boy.
https://cimg0.ibsrv.net/gimg/www.rx7...6b4fc35772.jpg https://cimg1.ibsrv.net/gimg/www.rx7...1cca228103.jpg https://cimg3.ibsrv.net/gimg/www.rx7...bf58803bb1.jpg https://cimg5.ibsrv.net/gimg/www.rx7...2c3707ce97.jpg https://cimg3.ibsrv.net/gimg/www.rx7...10ddefd768.jpg |
Slow progress. Anyone have any recommendations on where i should mount this relay and fuse block? I made a lot of slack on the harness, pretty much free to go anywhere on the passenger side of the cabin.
https://cimg2.ibsrv.net/gimg/www.rx7...4dab241cd3.jpg |
Just need to finish looming and this harness is done, finally!
https://cimg6.ibsrv.net/gimg/www.rx7...2f65d8e0b2.jpg https://cimg7.ibsrv.net/gimg/www.rx7...70a32e0190.jpg |
Harness finally complete. Wires ended up being tighter than I originally laid it out. Wanted to run the harness in the valley between the heads and the valve covers, but I'll have to settle with the stock location.
https://cimg0.ibsrv.net/gimg/www.rx7...0bab42b78f.jpg https://cimg1.ibsrv.net/gimg/www.rx7...b1c0a26784.jpg |
Oven Cleaner oxidized the aluminum a little bit, but ill be painting the valves covers and timing cover anyways.
https://cimg9.ibsrv.net/gimg/www.rx7...cc3ceabd1f.jpg https://cimg0.ibsrv.net/gimg/www.rx7...9f0bb725c8.jpg https://cimg1.ibsrv.net/gimg/www.rx7...f02ce4b14f.jpg |
Cam in. Valve springs in.
https://cimg2.ibsrv.net/gimg/www.rx7...1c9afd6b2a.jpg https://cimg4.ibsrv.net/gimg/www.rx7...7a0099a0d6.jpg https://cimg6.ibsrv.net/gimg/www.rx7...0ad56d55b7.jpg https://cimg7.ibsrv.net/gimg/www.rx7...a9899156b1.jpg https://cimg9.ibsrv.net/gimg/www.rx7...ea768ba20a.jpg https://cimg0.ibsrv.net/gimg/www.rx7...5f2b76e60e.jpg https://cimg1.ibsrv.net/gimg/www.rx7...600ebc5223.jpg https://cimg2.ibsrv.net/gimg/www.rx7...44bf86b86f.jpg https://cimg3.ibsrv.net/gimg/www.rx7...dafb261d2c.jpg |
|
Brake booster, windshield wiper motor and arms, windshield grill reinstalled. Front body harness cleaned up and wrapped with nylon.
https://cimg1.ibsrv.net/gimg/www.rx7...73a70f279e.jpg Mocking up intake manifold setup. 30lb injectors on the way. https://cimg8.ibsrv.net/gimg/www.rx7...11d8ced7d7.jpg |
New melling pump shimmed and installed. Water pump housing, alternator, pulleys, belt installed. Cracked my damn oil pan near the oil filter. 250 dollar mistake. Installed short tube headers. set the manifold on to see how its going to look. Did a little shooting on sunday as well.
https://cimg9.ibsrv.net/gimg/www.rx7...a18bff7d5c.jpg https://cimg0.ibsrv.net/gimg/www.rx7...cd3e9e8550.jpg https://cimg1.ibsrv.net/gimg/www.rx7...aeda43dd90.jpg https://cimg2.ibsrv.net/gimg/www.rx7...b19ab2d9ae.jpg https://cimg3.ibsrv.net/gimg/www.rx7...2c9f54aadf.jpg https://cimg4.ibsrv.net/gimg/www.rx7...6cf60ea453.jpg https://cimg5.ibsrv.net/gimg/www.rx7...595a29d9b9.jpg https://cimg6.ibsrv.net/gimg/www.rx7...23125ef3a6.jpg https://cimg7.ibsrv.net/gimg/www.rx7...cbbbd7bb26.jpg https://cimg8.ibsrv.net/gimg/www.rx7...c18b470153.jpg |
|
Finally found some motivation...
https://cimg2.ibsrv.net/gimg/www.rx7...3ad5c79ae8.jpg https://cimg3.ibsrv.net/gimg/www.rx7...ccb5bcc2a6.jpg https://cimg4.ibsrv.net/gimg/www.rx7...bafdae63b5.jpg https://cimg5.ibsrv.net/gimg/www.rx7...122bef7bdf.jpg https://cimg6.ibsrv.net/gimg/www.rx7...c68f298436.jpg https://cimg7.ibsrv.net/gimg/www.rx7...900378b02f.jpg |
All times are GMT -5. The time now is 11:43 AM. |
© 2024 MH Sub I, LLC dba Internet Brands