Boogy woogie
06-27-13, 03:28 PM
#51
Rotary Learner
Thread Starter
Join Date: May 2012
Location: missouri, east of kc
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
So between switching frames on a crotch rocket and working on some parts heres what i have got done. Not perfect by any means but nicely done for the time invested.
07-05-13, 11:57 AM
#52
Rotary Learner
Thread Starter
Join Date: May 2012
Location: missouri, east of kc
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
All my carb parts are in the hands of kansascityrepu to have some powdercoat layed down on it. Seen his collection and his project rx7 and im jealous.
07-11-13, 05:10 PM
#54
Rotary Learner
Thread Starter
Join Date: May 2012
Location: missouri, east of kc
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Most of my work is done with a hammer and chissle, drill & rotary bits, and bench grinder/ disk grinder. Although this time i had to also break out the bastard file.
07-30-13, 03:10 PM
#55
Rotary Learner
Thread Starter
Join Date: May 2012
Location: missouri, east of kc
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
So i had been super busy lately but with the car show coming up on august 24 i needed to make room for the rx7 so together the carb went after its been ppowdercoated. A few parts missed the powdercoater. 
07-31-13, 07:15 PM
#57
Your carb ....
Looks freaking AWESOME!
I love the powdercoated silver and the gunmetal (or unpainted aluminum?) look. I remember the black and green one you had posted in anther thread and thought that was pretty far out... This one is more subtle but it POPS out at you. Love the powdercoat that KC did.
I love the powdercoated silver and the gunmetal (or unpainted aluminum?) look. I remember the black and green one you had posted in anther thread and thought that was pretty far out... This one is more subtle but it POPS out at you. Love the powdercoat that KC did.
07-31-13, 11:16 PM
#58
Rotary Learner
Thread Starter
Join Date: May 2012
Location: missouri, east of kc
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Its chrome and gunmetal. Next time i would switch where i put the two. Whats chrome would be gunm and whats gunm would be chrome. Im very pleased with it. Cant wait to try it. When i took apart my last carb i found out the ao shot plunger got crooked and stuck from the gasket mod. 2 gaskets on both sides were to many. But i could not get it to idle low for nothing but it ran great. This carb i wanted it to look sleek and sick.
08-14-13, 11:40 PM
#61
Rotary Learner
Thread Starter
Join Date: May 2012
Location: missouri, east of kc
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
So once again i have a carb problem. 1 primary will not squirt fuel so ill have to see if something is blocking a jet. Otherwise with a modded intake i can still get fuel to both rotors and i can tell it will be a beast. And this different carb gasket kit was way better than the one from autozone everyone said you had to get. No leaks and no fittment problems at half the cost. Carshow is on the 24 so i have a busy road ahead of me.
