'83 GSL Refitting and Recovery in AZ
#52
Junior Member
Thread Starter
Join Date: Jan 2015
Location: Hereford, Arizona
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Ho-kay. I piddled around with the dash last night and today. Have one of those dash caps to replace the very attractive original.
Expect no quarter from the Arizona heat. Only the strongest, hardiest, tough as nails, and virile men can handle it.
So anyway, the goal is to get this thing glued on over the old dash.
I got a couple of Mitsubishi eyeball vents to replace the crumbling to dust old ones. After sanding down the old dash, taking out the high spots and digging out the old rotten foam, I filled the gaps with hot glue.
I used the rotary tool with sanding disk to trim out the rotten areas and clean up extra glue. Then I used my first generation Star Trek Phaser to heat up the glue and smooth it out.
The next step was to fit the dash cap. It was a little warped so I put some heat on it while holding it in position. Fit perfect after that. Squeezed out glue on the old dash. I only covered the edges leaving the main areas free to expand and contract.
Expect no quarter from the Arizona heat. Only the strongest, hardiest, tough as nails, and virile men can handle it.
So anyway, the goal is to get this thing glued on over the old dash.
I got a couple of Mitsubishi eyeball vents to replace the crumbling to dust old ones. After sanding down the old dash, taking out the high spots and digging out the old rotten foam, I filled the gaps with hot glue.
I used the rotary tool with sanding disk to trim out the rotten areas and clean up extra glue. Then I used my first generation Star Trek Phaser to heat up the glue and smooth it out.
The next step was to fit the dash cap. It was a little warped so I put some heat on it while holding it in position. Fit perfect after that. Squeezed out glue on the old dash. I only covered the edges leaving the main areas free to expand and contract.
#53
Junior Member
Thread Starter
Join Date: Jan 2015
Location: Hereford, Arizona
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Viola! The result.
Oh, here's a lucky find on eBay for $15.00 bucks. I felt like I found the Holy Grail.
I'll give the glue time to cure before I cover it with a high dollar genuine leather. I believe it's referred to as vinyl in the very best social circles.
Oh, here's a lucky find on eBay for $15.00 bucks. I felt like I found the Holy Grail.
I'll give the glue time to cure before I cover it with a high dollar genuine leather. I believe it's referred to as vinyl in the very best social circles.
#60
Junior Member
Thread Starter
Join Date: Jan 2015
Location: Hereford, Arizona
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
I read 350 to 390, but that sounds pretty high. I'll find it one way or another.
The glue I used to secure the dash cap was IPS Weld-On #16 Plastic Glue Cement for Acrylic - Plexiglass. I forgot to include that in the post.
The glue I used to secure the dash cap was IPS Weld-On #16 Plastic Glue Cement for Acrylic - Plexiglass. I forgot to include that in the post.
Last edited by HepCat58; 05-26-15 at 08:28 PM.
#63
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,835
Received 2,604 Likes
on
1,847 Posts
that turned out really nice!
#66
Junior Member
Thread Starter
Join Date: Jan 2015
Location: Hereford, Arizona
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
#67
Can Post Only in New Member Section
Join Date: May 2016
Location: Scottsdale
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
Seeking Cesar
I have had Cesar do work on my '83 RX7 and recently my phone crashed. I lost his number and I am trying to get a hold of him. Any help would be greatly appreciated. Thanks
Thread
Thread Starter
Forum
Replies
Last Post
NickNac113
1st Generation Specific (1979-1985)
13
10-01-15 09:25 PM