Dyno results... 424whp @ 18psi on e85
#1
Senior Member
Thread Starter
Join Date: Dec 2004
Location: Minot, ND
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
Dyno results... 424whp @ 18psi on e85
I know I'd already posted the results in the e85 thread that I have going right now, but I thought I'd make a thread on my results from the weekend. I made the trip down to Sioux Falls, SD, and Joey from Excessive did the tuning for me. We were able to tune to 424whp @ 18psi. I am waiting for him to get back in touch with me on some of the details such as injector duty cycle, timing, a/f, etc. Mods are as follows:
Stock motor
Precision t4 pt67
sls custom manifold
sls vmount ic setup
tial 44mm wg
tial bov
aem ems
aem ignition
aem wbo2
850/1600 injectors
dual walbro fuel pumps
Be happy to hear your thoughts, and I'll post up the dyno sheet later today.
Stock motor
Precision t4 pt67
sls custom manifold
sls vmount ic setup
tial 44mm wg
tial bov
aem ems
aem ignition
aem wbo2
850/1600 injectors
dual walbro fuel pumps
Be happy to hear your thoughts, and I'll post up the dyno sheet later today.
#5
Senior Member
Thread Starter
Join Date: Dec 2004
Location: Minot, ND
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#8
I know I'd already posted the results in the e85 thread that I have going right now, but I thought I'd make a thread on my results from the weekend. I made the trip down to Sioux Falls, SD, and Joey from Excessive did the tuning for me. We were able to tune to 424whp @ 18psi. I am waiting for him to get back in touch with me on some of the details such as injector duty cycle, timing, a/f, etc. Mods are as follows:
Stock motor
Precision t4 pt67
sls custom manifold
sls vmount ic setup
tial 44mm wg
tial bov
aem ems
aem ignition
aem wbo2
850/1600 injectors
dual walbro fuel pumps
Be happy to hear your thoughts, and I'll post up the dyno sheet later today.
Stock motor
Precision t4 pt67
sls custom manifold
sls vmount ic setup
tial 44mm wg
tial bov
aem ems
aem ignition
aem wbo2
850/1600 injectors
dual walbro fuel pumps
Be happy to hear your thoughts, and I'll post up the dyno sheet later today.
How far can you go with 280l/h pump and 850/1600 using resistors?
#9
Senior Member
Thread Starter
Join Date: Dec 2004
Location: Minot, ND
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
resisitors. I have the ultimate fuel package from Jason at rx7store.net.
I'm not sure what to tell you, my personal experience is only on dual walbro 255 pumps.
I'm not sure what to tell you, my personal experience is only on dual walbro 255 pumps.
#10
Rotary Enthusiast
iTrader: (3)
Join Date: Jan 2007
Location: st. louis
Posts: 1,000
Likes: 0
Received 0 Likes
on
0 Posts
How long have you been running the walbro pumps? They do not claim to be flex fuel rated. Also, did you replace the injector orings and such on your injectors or were they already flex fuel injectors?
Data logs of the runs would be awesome.
Data logs of the runs would be awesome.
#15
Senior Member
Thread Starter
Join Date: Dec 2004
Location: Minot, ND
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
turbo crapped on me which is why I haven't been able to get you guys logs yet... turbo went off today, so as soon as I get it back I'll provide some more of you guys more info on my drive ability, and some logs to see how it all works with the e85.
#16
Chasing numbers
iTrader: (5)
stock ports
glad to see you posting this info here. I have been wondering about this e85 but decided to wait to here more results as I do not want to be a tester.,. On the stock ports, thats great numbers. I made if I recall correctly 430 at 20psi area on a 40r (w/ stockports). But this was real lean, not as safe as I bet yours are..
#18
Senior Member
Thread Starter
Join Date: Dec 2004
Location: Minot, ND
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
I"m curious after all this dyno tuning, and having my turbo go out on me only a mile or so after taking it off the trailer, if my numbers are legit, or if that hurt my numbers. Also I have an intake temp issue. the shop that did my setup, didn't finish the v mount design, so my radiator is heat soaking my intercooler. so I need to get that finished, and get some sheet metal ducting in there. whatever little things could I look at to get my closer to my goal of 500whp without messing too much with my tune. what potentially could I pick up with a different lim. whatabout aftermarket uims? are any worthwhile? thanks for the feedback guys.
#19
Senior Member
Join Date: Oct 2005
Location: Kirkland, WA
Posts: 324
Likes: 0
Received 0 Likes
on
0 Posts
are you using the 3ohm resistors that came with rx7 store? I tried those with my aem ecu and the ecu could not reliably control them at all. Half the time they just wouldnt do anything. I swapped to 10ohm resistors and all was well, i just had a whole lot of injector lag that i had to account for. Also, if you dont mind, i would be interested to see what your map looks like.
#21
Senior Member
Thread Starter
Join Date: Dec 2004
Location: Minot, ND
Posts: 345
Likes: 0
Received 0 Likes
on
0 Posts
yeah I'm using the resistors that came with the rx7 store fuel package.
goodfella... my guess is it was a bearing failure. my compressor wheel hit the housing, taking chunkcs out of the wheel. when taken off the car, I could push from the back side, and move the entire center cartridge forward, and then from the front side push it back... had some definitely play. I'll find out exactly what's wrong, and what is gonna have to be replaced when I get the phone call from Precision.
goodfella... my guess is it was a bearing failure. my compressor wheel hit the housing, taking chunkcs out of the wheel. when taken off the car, I could push from the back side, and move the entire center cartridge forward, and then from the front side push it back... had some definitely play. I'll find out exactly what's wrong, and what is gonna have to be replaced when I get the phone call from Precision.
Thread
Thread Starter
Forum
Replies
Last Post
HalifaxFD
Canadian Forum
126
05-09-16 07:06 PM