Adaptronic PNP, seq. twins, direct fire, and ffe trigger
#1
PNP, seq. twins, direct fire, and ffe trigger
I stupidly bought a bunch of upgrades without ensuring if they would work with the adaptronic ecu. I am running the BNR twins on sequential. I would like to run my AEM coils in direct fire along with the FFE trigger. Looks like I can't run the AEM coils on direct fire, has there been any updates to fix this? Also, it looks like the FFE trigger will only run direct fire. Going non-sequential is not an option. Anybody have any experience trying to make this setup work?
#2
Senior Member
iTrader: (2)
You can run the coils and trigger in direct fire. There are several posts from Andy and mark (adaptronic) and from Elliot from turblown eng in this section do a search and you'll fiond them. How to wire it up and all. You may also want to head over to the adaptronic forums there are quite a bit of base maps over there Andy and mark are more likely to answer you there first..
Read this post: https://www.rx7club.com/adaptronic-e...tings-1066512/ it has the pinouts to run direct fire and some basemaps.
Where did you buy the coils? was it a complete kit with wiring?
Read this post: https://www.rx7club.com/adaptronic-e...tings-1066512/ it has the pinouts to run direct fire and some basemaps.
Where did you buy the coils? was it a complete kit with wiring?
Last edited by knotsonice; 06-06-16 at 09:56 PM.
#4
You can run the coils and trigger in direct fire. There are several posts from Andy and mark (adaptronic) and from Elliot from turblown eng in this section do a search and you'll fiond them. How to wire it up and all. You may also want to head over to the adaptronic forums there are quite a bit of base maps over there Andy and mark are more likely to answer you there first..
Read this post: https://www.rx7club.com/adaptronic-e...tings-1066512/ it has the pinouts to run direct fire and some basemaps.
Where did you buy the coils? was it a complete kit with wiring?
Read this post: https://www.rx7club.com/adaptronic-e...tings-1066512/ it has the pinouts to run direct fire and some basemaps.
Where did you buy the coils? was it a complete kit with wiring?
Thanks for replying. I got the coil kit from Sakebomb. To be clear, I want to run direct fire with twin sequential setup. From what I've searched, direct fire uses up the aux output designated for the turbo pre-control (in sequential mode) therefore disabling sequential turbo operation. Someone did mention using the OMP output to drive the pre-control but I don't see much information on that. Sorry if I missed something.
#5
Senior Member
iTrader: (2)
A few notes in here: https://www.rx7club.com/adaptronic-e...spool-1097517/
I'm running '99 twin in seq: I used 4L and or 4J on the factory pin for twin turbo precontrol. AUX7 in the adaptronic. Wired the solenoids to the MOP wiring. But i'm also using AEKnightz Solenoid kit.
I'm running '99 twin in seq: I used 4L and or 4J on the factory pin for twin turbo precontrol. AUX7 in the adaptronic. Wired the solenoids to the MOP wiring. But i'm also using AEKnightz Solenoid kit.
#6
A few notes in here: https://www.rx7club.com/adaptronic-e...spool-1097517/
I'm running '99 twin in seq: I used 4L and or 4J on the factory pin for twin turbo precontrol. AUX7 in the adaptronic. Wired the solenoids to the MOP wiring. But i'm also using AEKnightz Solenoid kit.
I'm running '99 twin in seq: I used 4L and or 4J on the factory pin for twin turbo precontrol. AUX7 in the adaptronic. Wired the solenoids to the MOP wiring. But i'm also using AEKnightz Solenoid kit.
Thread
Thread Starter
Forum
Replies
Last Post
Adaptronic Adaptronic PWM Decisions/Setup
jreynish
Adaptronic Engine Mgmt - AUS
10
07-26-16 06:23 PM
filoralph
3rd Generation Specific (1993-2002)
4
04-07-16 05:00 PM