3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

used fd motors

Thread Tools
 
Search this Thread
 
Old Feb 21, 2005 | 11:39 PM
  #1  
phantom works's Avatar
Thread Starter
17,600 hp everyday!
Tenured Member 05 Years
iTrader: (3)
 
Joined: May 2004
Posts: 331
Likes: 0
From: SoCal
used fd motors

whats a used low milage fd motor going for now days?
with turbos and all the stuff that goes with it.
Reply
Old Feb 21, 2005 | 11:49 PM
  #2  
iluvmy3rdgen's Avatar
I live in a Museum
Tenured Member 05 Years
 
Joined: Apr 2004
Posts: 928
Likes: 0
From: NY, 10992
Originally Posted by phantom works
whats a used low milage fd motor going for now days?
with turbos and all the stuff that goes with it.

Search, They usually come with tranny, turbos, everything, but sometimes a clipped harness, but the harness is for a RHD car so if your car is left hand drive you can't use the harness anyway.
Reply
Old Feb 22, 2005 | 12:54 AM
  #3  
phantom works's Avatar
Thread Starter
17,600 hp everyday!
Tenured Member 05 Years
iTrader: (3)
 
Joined: May 2004
Posts: 331
Likes: 0
From: SoCal
the reason I'm asking is because I'm pulling a mazda reman w/33,000 miles out of my car. the turbos were replaced at the same time and mazda did the work.
motor is still strong w/no problems so I don't want to ask to much for it but at the same time I don't want to ask to little.

why am I taking it out, I was high and decided to do an engine swap so the motor and trans are coming out.
Reply
Old Feb 22, 2005 | 01:44 AM
  #4  
d0 Luck's Avatar
raysspl.com
Tenured Member 10 Years
 
Joined: Sep 2003
Posts: 3,508
Likes: 0
From: L.A.
Originally Posted by phantom works
why am I taking it out, I was high and decided to do an engine swap so the motor and trans are coming out.
well maybe you're high right now too
Reply
Old Feb 22, 2005 | 09:30 AM
  #5  
DaleClark's Avatar
RX-7 Bad Ass
Tenured Member: 20 Years
Liked
Loved
Community Favorite
iTrader: (56)
 
Joined: Jan 2002
Posts: 15,622
Likes: 2,725
From: Pensacola, FL
I'd say about $1500-2000 would be a fair price. Might be able to get more selling each component individually - turbos, manifolds, injectors, etc. That would just take more time and work, though, than selling the whole works as a unit.

Dale
Reply
Old Feb 22, 2005 | 09:37 AM
  #6  
Herblenny's Avatar
DGRR 2017 4/26-4/30, 2017
Tenured Member 20 Years
iTrader: (13)
 
Joined: Nov 2001
Posts: 13,597
Likes: 6
From: Alabama
I sold my short block, tested on a crank table, ran for 2 hours, put on new front cover gasket and new pan pan seal for $1500 shipped.. But that was for a friend..
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
doritoloco
New Member RX-7 Technical
7
Sep 5, 2015 12:41 PM




All times are GMT -5. The time now is 04:06 AM.