3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Trust Exhaust Install

Thread Tools
 
Search this Thread
 
Old Apr 11, 2003 | 11:14 PM
  #1  
Thread Starter
Senior Member
Tenured Member 15 Years
 
Joined: Jun 2002
Posts: 725
Likes: 0
From: Plano, TX
Trust Exhaust Install

Just installed the Trust N1 exhaust on my fd. I think its an n1 but i do know that it is a trust. The thing sounds so good its amazing. My car finally sounds like it has a rotary. Install of course only took 20 minutes of course. Afterwards we were driving and shooting out major fireballs and i mean major i could see the tops of them coming over my spoiler it was a beautiful sight to see which i had a video of it. Shot one of right in front of a suburban with about 10 people in it and they were dumbfounded when they pulled up to us at the light. It looks so good and the rear of that car its a sight to see.

Everyone and anyone tried to race us that night we smoked a gst eclipse a few mustangs and then a vette which was particulary nice for me which gives me a place of knowing about how fast my car is right now. The best was just beating up on all of the people who had no idea what was coming at all it was awesome.

Intake and powerfc with commander coming near at the end of may so I can have some serious power and smoke many of many of cars. Wish me luck.
Reply
Old Apr 11, 2003 | 11:22 PM
  #2  
Full Member
Tenured Member 10 Years
 
Joined: Oct 2002
Posts: 103
Likes: 0
From: Hawaii
Good Luck! Hope you do a lot of smoking. Ha Ha.
Reply
Old Apr 11, 2003 | 11:24 PM
  #3  
Dougie_fresh_007's Avatar
Full Member
Tenured Member 05 Years
 
Joined: Jan 2003
Posts: 220
Likes: 0
From: tracy california
sounds like you are off to a good plan... when u get the power fc check that area of the forum and u can shoot some HUGE flames... what are your other mods... midpipe?.....

anywayz congrats on everything... and good luck
Reply
Old Apr 12, 2003 | 01:39 AM
  #4  
Antiny's Avatar
Junior Member
Tenured Member 10 Years
 
Joined: Apr 2003
Posts: 10
Likes: 0
From: California
Can you describe the sound of the exhaust? I am looking for an exhaust myself, haven't found one that I quite like yet.
Reply
Old Apr 12, 2003 | 01:57 PM
  #5  
Thread Starter
Senior Member
Tenured Member 15 Years
 
Joined: Jun 2002
Posts: 725
Likes: 0
From: Plano, TX
its hard to describe what the car sounds like. ill have to get a clip of what it sounds like so you can hear it as well. pm me with your email and ill try to figure out this email gig and send it to ya. It does sound a little different though because it has a street port done and a fully built motor. its not as loud as it could be because i am running a cat and the midpipe is coming soon need to talk to rotary about getting one very very soon. if you want that clip let me know.

so close to being an absolute terror on the street.
Reply
Old Apr 12, 2003 | 02:03 PM
  #6  
Thread Starter
Senior Member
Tenured Member 15 Years
 
Joined: Jun 2002
Posts: 725
Likes: 0
From: Plano, TX
dougie,

the other mods that i have include...

act s/s clutch
fidanza flywheel 9.5 lb
stainless steel downpipe
silicon hose job
block off plate kit
ast from rotary
fluidyne radiator
rotary performance street port
3mm apex seals
trust exhaust
rebuilt tranny

coming soon very very soon...

trust airinx unit
power fc with commander
tein ha suspension with edfc

must decide whether to go single or to do the bnr stage 3's or the efini twins who knows what to do. but those are the current and so far future mods wish i had to the cash to do it all right now.
Reply
Old Apr 13, 2003 | 02:10 AM
  #7  
Antiny's Avatar
Junior Member
Tenured Member 10 Years
 
Joined: Apr 2003
Posts: 10
Likes: 0
From: California
Thanks, that would help me out a lot. What i'm looking for is a good deep sounding exhaust. I don't wanna sound like a shakin up tin can full of bee's!! I hear that the RB Dual exhaust sounds good, but I like the single exhuast look. I was thinking about the Greddy exhaust also.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Th0m4s
Build Threads
25
Feb 26, 2019 02:04 AM
astrum
2nd Generation Specific (1986-1992)
24
Nov 15, 2017 08:44 AM
GrossPolluter
General Rotary Tech Support
7
Aug 22, 2015 11:23 PM
gabescanlon
Interior / Exterior / Audio
1
Aug 11, 2015 05:59 PM




All times are GMT -5. The time now is 04:58 PM.