3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

stalls after startup, only one time, then runs fine

Thread Tools
 
Search this Thread
 
Old 11-10-06, 08:42 AM
  #1  
proper motoring

Thread Starter
 
pugg57's Avatar
 
Join Date: Jan 2004
Location: USA
Posts: 1,706
Likes: 0
Received 1 Like on 1 Post
stalls after startup, only one time, then runs fine

lately, when i start the FD i've been having this weird problem. the first time i "come down of the rpms", like pushing in the clutch and coming to a stop, my car wants to stall, sometimes it does, sometimes i can catch it with the throttle. i can start it right back up when it does and after that, it runs fine until the next day that i drive it. what the heck could be causing this?

mods: PFC, Apex'i Power Intake, 3" DP, RB dual tip cat-back, PFS plug wires

i just had all of my vacuum lines, plug wires, and plugs replaced by PF Supercars less than 1.5k miles ago.

Last edited by pugg57; 11-10-06 at 08:44 AM.
Old 11-10-06, 01:26 PM
  #2  
Full Member

 
rx7playa's Avatar
 
Join Date: Feb 2006
Location: Richmond, Virginia
Posts: 138
Likes: 0
Received 0 Likes on 0 Posts
I have the same problem, if I do not drive my car for a few days the first time that I do start it up it wants to stall. Normaly if I try to pull it out of the garage it will cut off. The only way that I can get it not to do it, is to let the car idle for a few minutes before I drive it. I would also like to know what causes this.
Old 11-10-06, 10:14 PM
  #3  
proper motoring

Thread Starter
 
pugg57's Avatar
 
Join Date: Jan 2004
Location: USA
Posts: 1,706
Likes: 0
Received 1 Like on 1 Post
see, its funny that you say that, because i've only recently been letting the car sit for days at a time between drives. i wonder if its something weird with fuel evaporating from the lines or something while it sits... or something weird like that.

any help out there???
Old 11-10-06, 10:24 PM
  #4  
Warming the planet.

 
Gadd's Avatar
 
Join Date: Dec 2004
Location: Chico, CA
Posts: 845
Likes: 0
Received 2 Likes on 2 Posts
I assuming you mean the car is still cold when it happens. Check to see if the dashpot is adjusted and operating properly. And/or adjust the water temp correction in the PFC for temp the car is stalling at.
Old 11-11-06, 03:35 AM
  #5  
Full Member

 
dlarson101's Avatar
 
Join Date: Nov 2002
Location: Denver, CO
Posts: 93
Received 0 Likes on 0 Posts
i just had all of my vacuum lines, plug wires, and plugs replaced by PF Supercars less than 1.5k miles ago.[/QUOTE]


Soooooo..... when did your problem start happening?
Old 11-11-06, 07:36 PM
  #6  
proper motoring

Thread Starter
 
pugg57's Avatar
 
Join Date: Jan 2004
Location: USA
Posts: 1,706
Likes: 0
Received 1 Like on 1 Post
Originally Posted by dlarson101
i just had all of my vacuum lines, plug wires, and plugs replaced by PF Supercars less than 1.5k miles ago.

Soooooo..... when did your problem start happening?[/QUOTE]
problem started about 500 miles after having all the work done... at least, that was the first time i noticed it.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Kyo
2nd Generation Specific (1986-1992)
6
04-13-19 09:24 AM
sherff
Adaptronic Engine Mgmt - AUS
9
02-24-19 12:09 PM
alphawolff
1st Generation Specific (1979-1985)
17
11-17-15 05:57 PM



Quick Reply: stalls after startup, only one time, then runs fine



All times are GMT -5. The time now is 04:17 AM.