SMIC w/ stock twins,downpipe,apex intake and microtech comp.
#1
SMIC w/ stock twins,downpipe,apex intake and microtech comp.
460mm X 310mm X 85mm
SUPER HUGE 85mm THICK
( 3.25" THICK )
( 18" LONG )
( 12" HIGH )
2.5" INLET AND OUTLET
SUPER BAR AND PLATE
2.5" inlet, 2.5" outlet
i am looking for a smic for my 93 rx7. this intercooler i am looking at above has the inlet and outlet on opposite sides instead of bottom and top. {top inlet, top outlet} is the fatory top and bottom setup better than this one?, or does it make a difference in cooling airflow? this is the link below to the smic i am looking at. please give me any info you may offer.
http://search.ebay.com/rx7-smic_W0QQsojsZ1QQfromZR40
SUPER HUGE 85mm THICK
( 3.25" THICK )
( 18" LONG )
( 12" HIGH )
2.5" INLET AND OUTLET
SUPER BAR AND PLATE
2.5" inlet, 2.5" outlet
i am looking for a smic for my 93 rx7. this intercooler i am looking at above has the inlet and outlet on opposite sides instead of bottom and top. {top inlet, top outlet} is the fatory top and bottom setup better than this one?, or does it make a difference in cooling airflow? this is the link below to the smic i am looking at. please give me any info you may offer.
http://search.ebay.com/rx7-smic_W0QQsojsZ1QQfromZR40
#2
Wankel Shmankel
Join Date: Mar 2005
Location: Oahu (Hawaii)
Posts: 627
Likes: 0
Received 0 Likes
on
0 Posts
^ teh suck
Unless you want to use your stock ic duct & fabricate your own piping, buy a name brand one similar to one shown here
http://www.rx7store.net/index.asp?Pa...S&Category=215
Of course, the closest thing is a asp med smic. ~$1200 or so - a lot more expensive but bigger & quality build.
One way to fab a kit is to find someone to buy a duct off of. You can probably use the asp y-pipe crossover pipe to go to the hot side of the turbo. If you have the greddy 3 piece pipe kit, you can probably bend their pipe that leads to the greddy elbow.
This is only an idea I'm throwing out. I have no idea if the asp pipe will mate to the ebay intercooler or if the greddy pipes or duct will fit either.
Unless you want to use your stock ic duct & fabricate your own piping, buy a name brand one similar to one shown here
http://www.rx7store.net/index.asp?Pa...S&Category=215
Of course, the closest thing is a asp med smic. ~$1200 or so - a lot more expensive but bigger & quality build.
One way to fab a kit is to find someone to buy a duct off of. You can probably use the asp y-pipe crossover pipe to go to the hot side of the turbo. If you have the greddy 3 piece pipe kit, you can probably bend their pipe that leads to the greddy elbow.
This is only an idea I'm throwing out. I have no idea if the asp pipe will mate to the ebay intercooler or if the greddy pipes or duct will fit either.
#3
there is a newer smic by the same company that comes with pipes nice couplers and t-bolts. and I have your duct right here.
https://www.rx7club.com/group-buy-center-69/gb-fiberglass-duct-xspower-intercooler-ends-11-11-05-a-476815/
https://www.rx7club.com/group-buy-center-69/gb-fiberglass-duct-xspower-intercooler-ends-11-11-05-a-476815/
Thread
Thread Starter
Forum
Replies
Last Post