No. The GReddy Airinx is the only dual intake kit that will work well with the GReddy Type 24 V-spec FMIC...

 

And let me tell you, the Greddy Airinx with my Greddy FMIC is a SUPER tight fit. I just finished the Greddy Airinx install tonight and the lower filter rests against both the radiator pipe and intercooler pipes. I will post some pics tomorrow when I get a chance.

 

Has anyone tried the Knight Sports V-Mount set-up? I want to hear how that baby works.

- Steiner

 

Below is my intercooler setup. Its in ugly form, and it will be completed from being polished on Friday.

Side view:


Other side view:


Bumper installed:


Its a beefy one. It is 36" by 18" by 4.5 "

I will show more pictures next week after it is all polished.

Mike

 

Is that MVA motorsports custom work? Nice 20b and single turbo

 

Yep. Good eye. All the parts in the engine bay will be polished by COB Friday.

Wheeeeeeeeeeeee

Mike

 

20B and big single? Well, duh! No wonder the IC core is so huge!

 

But fed through a stock nose? Not to be so blunt but half that core won't even see any flow. You need an aftermarket nose! Maybe a GTC
Regards,
Crispy

 

No was has tried the knight sports?

- Steiner

 

Below is my intercooler setup. Its in ugly form, and it will be completed from being polished on Friday
------------------------------------------------------------------------
Red - Rx7

Sorry but that looks real nice to me.

 

Chris, I have the same problem with the GReddy Type 24 V-spec; the upper half of the IC core isn't getting ram air...

 

While the nose is not completely open to the air, the ducting around the IC will allow the air to hit the full front facia from the IC.

I plan on putting a different front bumper, but right now I am out of money. Anyone want to hand some over?

80-CU.IN.T: Thanks, it looks good... but wait till its all purdy.

Mike

 

hey red....what head lights are those....looks really clean.

 

What's the difference between an H mount and a V mount? They both look to have the same positioning or attitude, but being infront of the engine of course, that IC's that sit over the engine have, or am I mistaken.

 

how come nobody addresses the inefficiency of tube and fin cores??

 

 

https://www.rx7club.com/forum/showth...25#post1535825

 

Where did you get those intake pipes? They're nice!

 

HKS RS (racing suction) intakes. comes with two polished pipes for each turbo. i got them from japan a while back.. you can get them now in the US through a HKS dealer for around 500 bucks. go to HKS's website for more info.



pic when my car only had a ypipe and intakes

 

this is pretty too!!!!!!

 

That picture has been photoshoped for sharpness. (The one above).

But otherwise looks nice.

 

I have the HKS Type S Front Mount Intercooler. It is very large 12x24x3 and now need a new front bumper with a larger hole to take advantage of its cooling capabilities. The installation was pretty tough though considering all the brackets didn't match up perfect and had to make a few custom extentions so they would bolt up. I am very happy with the intercooler and if I ever had to do it over I would choose the same one. I have had it for about 5 months or so.

[IMG]C:\Program Files\WindowsUpdate\New Folder\THE folder\My Pics\My RX-7\New Pics\rx7_front3.jpg[/IMG]

 

man didn't work. lets try again

[IMG]C:\Program Files\WindowsUpdate\New Folder\THE folder\My Pics\My RX-7\New Pics\rx7_front3[/IMG]

 

dammit that really sucks. My bad.

last try. i know this will work.

http://www.imagestation.com/mypictur...ion=rx7_front3

 

So does Rx7fashion still sell their IC's? If so how much? I dont see it on their webiste anymore.