Nice way to clean/ brighten the UIM
01-29-06, 08:02 PM
#1
Nice way to clean/ brighten the UIM
I was tired of my UIM lookin old and grimy so if you want it to look kinda shiny and new looking again here you go.
What you need: Steel wool, Engine degreaser, wire brush, wet/soap towel, dry towel, aluminum cleaner or polish
What to do: 1) Wire brush the UIM, get it everywhere but dont go for too long 2) Spray engine degreaser 3) Use the steel wool and get everywhere on the UIM, it will leave particles of the steel wool and look gunmetal 4) Wipe this down with your wet/soapy towel 5) Repeat 2-4 until you get it pretty close to what you want 6) apply aluminum cleaner or polish and wipe down
It should be nice, clean, and bright silver now. I will post pics of before and after in about 10 minutes.
What you need: Steel wool, Engine degreaser, wire brush, wet/soap towel, dry towel, aluminum cleaner or polish
What to do: 1) Wire brush the UIM, get it everywhere but dont go for too long 2) Spray engine degreaser 3) Use the steel wool and get everywhere on the UIM, it will leave particles of the steel wool and look gunmetal 4) Wipe this down with your wet/soapy towel 5) Repeat 2-4 until you get it pretty close to what you want 6) apply aluminum cleaner or polish and wipe down
It should be nice, clean, and bright silver now. I will post pics of before and after in about 10 minutes.
01-29-06, 08:42 PM
#6
Where has my $ gone?
iTrader: (12)
Join Date: Feb 2004
Location: Bay Area, Cal/Phoenix, AZ
Posts: 1,654
Likes: 0
Received 7 Likes
on
2 Posts
Originally Posted by rx7what
bead blasting works nice too.
Trending Topics
01-29-06, 08:49 PM
#8
Originally Posted by DMoneyRX-7
I didnt even remove the UIM though. It took me like 20-30 min. I was just trying to get it looking nice, new, and a lil shiny. Worked for me. What the hell is bead blasting. Havn't heard of it.
I am doing a upper and lower manifold right now as well.
01-29-06, 08:50 PM
#9
Rotary Freak
iTrader: (1)
Join Date: Oct 2003
Location: Hampton, Va
Posts: 2,506
Likes: 0
Received 0 Likes
on
0 Posts
That's a damn good job DMoney! Especially with the tools you used and the fact that you didn't even have to remove the UIM. I know what I'm doin' when I get some spare time....
01-29-06, 08:56 PM
#10
Ya, I would rather just save my money than get someone to polish my UIM and LIM. I mean i know ceramic coating it is benificial but its just not one of those things i care for. Im sure if you sand, steel wool, wire brush, and polish the UIM a lil more than i did it will look really polished. I kinda want this to be a sticky because it took me some searching and came up with nothing. For the saved money and time you get from doing this i think its worthy. But hell what do i know. So dont flame me for the last comment please.
01-29-06, 09:53 PM
#12
RX-7 Bad Ass
iTrader: (55)
I'm a fan of clean, nice looking cast aluminum parts. Unfortunately, it's VERY hard to keep it looking nice - anything abrasive will polish the part to some extent. Bead blasting is one of the few ways to do it.
You actually use glass beads to clean the part - doesn't look like beads that you'd think, actually it's like a very fine sand in appearance and texture. Harbor Freight sells blast cabinets for around $100 or so - it's just a large cabinet that has gloves and a blast nozzle.
http://www.harborfreight.com/cpi/cta...emnumber=38440
You do have to have an air compressor, though. But, bead blasting a part can clean up stuff like you wouldn't believe.
Your UIM turned out really nice, though! Little work like that in the engine bay can really clean things up and make it much nicer.
Dale
You actually use glass beads to clean the part - doesn't look like beads that you'd think, actually it's like a very fine sand in appearance and texture. Harbor Freight sells blast cabinets for around $100 or so - it's just a large cabinet that has gloves and a blast nozzle.
http://www.harborfreight.com/cpi/cta...emnumber=38440
You do have to have an air compressor, though. But, bead blasting a part can clean up stuff like you wouldn't believe.
Your UIM turned out really nice, though! Little work like that in the engine bay can really clean things up and make it much nicer.
Dale
01-30-06, 03:21 AM
#14
Originally Posted by DaleClark
I'm a fan of clean, nice looking cast aluminum parts. Unfortunately, it's VERY hard to keep it looking nice - anything abrasive will polish the part to some extent. Bead blasting is one of the few ways to do it.
You actually use glass beads to clean the part - doesn't look like beads that you'd think, actually it's like a very fine sand in appearance and texture. Harbor Freight sells blast cabinets for around $100 or so - it's just a large cabinet that has gloves and a blast nozzle.
http://www.harborfreight.com/cpi/cta...emnumber=38440
You do have to have an air compressor, though. But, bead blasting a part can clean up stuff like you wouldn't believe.
Your UIM turned out really nice, though! Little work like that in the engine bay can really clean things up and make it much nicer.
Dale
You actually use glass beads to clean the part - doesn't look like beads that you'd think, actually it's like a very fine sand in appearance and texture. Harbor Freight sells blast cabinets for around $100 or so - it's just a large cabinet that has gloves and a blast nozzle.
http://www.harborfreight.com/cpi/cta...emnumber=38440
You do have to have an air compressor, though. But, bead blasting a part can clean up stuff like you wouldn't believe.
Your UIM turned out really nice, though! Little work like that in the engine bay can really clean things up and make it much nicer.
Dale
01-30-06, 12:38 PM
#15
Tequila? ..it's like beer
iTrader: (1)
Join Date: Mar 2001
Location: Woodbine, MD
Posts: 1,124
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by HDP
I thought you would use walnut shells on soft metals like aluminum? I could be wrong.
01-30-06, 12:40 PM
#16
Rotary Freak
I polished two UIM/TB using my Dremel/Drill and some sanding discs and buffing wheels. It is not and easy job to do. It must have taken over 20+ hours in total to do each set. Good thing I was unemployed at the time.
.
01-30-06, 05:56 PM
#18
BTW, steel wool is my new best friend. Look at the alternator and you can see a part of it that i started to work on. Then i noticed that the metal shavings from the wool were being attracted to it since its an electric motor. When i have alot of spare time i will take the alternator off and clean it like i did my UIM. Now im going back outside to do the rear turbine intake.
01-31-06, 12:25 PM
#24
What's your point ?
Join Date: Feb 2001
Location: Gainesville, Fla.
Posts: 3,573
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MakoRacing
Yeah I have an extra LIM, UIM, TB so I bead blasted them and Im hand sanding them and polishing them....lots of work
When you get finished with them give us an idea of how many hours you wind up with in doing them and the results. Not to mention how your hands and arms feel while your doing it. (-:
01-31-06, 12:35 PM
#25
What's your point ?
Join Date: Feb 2001
Location: Gainesville, Fla.
Posts: 3,573
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by DMoneyRX-7
BTW, steel wool is my new best friend. Look at the alternator and you can see a part of it that i started to work on. Then i noticed that the metal shavings from the wool were being attracted to it since its an electric motor. When i have alot of spare time i will take the alternator off and clean it like i did my UIM. Now im going back outside to do the rear turbine intake.
Steel wool won't be your best friend when all the little steel pieces get into you alternator and cause it to fail. You do realize all the little sttle particles will begin to cause rust stains everywhere they land, collect, and get wet. I have to admitt it looks worlds better. I'm just hate to say that using steelwool with parts still in the engine bay will be really hard to clean out and will deffinately start causing rust stains, after all you did use soap and "water" as well so it won't be long before you start seeing the rust.