RX7Club.com - Mazda RX7 Forum

3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:
Full Detail Automotive

Newbee engine pull question

Thread Tools
 
Search this Thread
 
Old 07-26-08, 12:02 PM
  #1  
LS_1 FD
Thread Starter
iTrader: (4)
 
andygoesfast's Avatar
 
Join Date: Jul 2008
Location: Sonora CA
Posts: 74
Likes: 0
Received 0 Likes on 0 Posts
Talking Newbee engine pull question
So I got my fd with a blown up motor. The new one just shipped and I was wondering is it quicker to pull the motor and trans together or just the engine?

Thanks a lot for any input.
andygoesfast is offline  
Reply Like
Old 07-26-08, 12:03 PM
  #2  
Mr. Links

iTrader: (1)
 
Mahjik's Avatar
 
Join Date: Aug 2001
Location: Kansas City, MO
Posts: 27,595
Received 40 Likes on 26 Posts
Arrow
Check this thread:

https://www.rx7club.com/3rd-generation-specific-1993-2002-16/engine-removal-question-772707/
Mahjik is offline  
Reply Like
Old 07-26-08, 12:07 PM
  #3  
LS_1 FD
Thread Starter
iTrader: (4)
 
andygoesfast's Avatar
 
Join Date: Jul 2008
Location: Sonora CA
Posts: 74
Likes: 0
Received 0 Likes on 0 Posts
Thanks alot I look and didnt find it !!!
andygoesfast is offline  
Reply Like
Old 07-26-08, 12:10 PM
  #4  
slurpee

iTrader: (3)
 
FD3Smaniac's Avatar
 
Join Date: Apr 2004
Location: Flint, Michigan
Posts: 723
Likes: 0
Received 1 Like on 1 Post
pull the engine with the tranny. You can drop a new clutch in easier, and then assemble outside of the car making installation a lot easier.
FD3Smaniac is offline  
Reply Like
Old 07-26-08, 12:50 PM
  #5  
LS_1 FD
Thread Starter
iTrader: (4)
 
andygoesfast's Avatar
 
Join Date: Jul 2008
Location: Sonora CA
Posts: 74
Likes: 0
Received 0 Likes on 0 Posts
After watching that video on u tube, I think I am just going to pull them together so I can check out the tans also.
thanks for the quick response
andygoesfast is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Installed UIM gasket, now my engine won't run
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
1979 Barn Find - Unable to idle
alphawolff
1st Generation Specific (1979-1985)
17
11-17-15 05:57 PM
10AE throttle sticking / RPMs surging
CaptainKRM
2nd Generation Specific (1986-1992)
14
08-26-15 09:52 PM
Can ungrounded wire cause the odometer not to work
maikelc
3rd Generation Specific (1993-2002)
8
08-24-15 11:04 AM
Wiring harness question
Professorpeanutrx7
New Member RX-7 Technical
5
08-15-15 01:38 PM
Back to Subforum
3rd Generation Specific (1993-2002)
View Next Unread
Ecu Needed.....




Advanced Search
Quick Reply: Newbee engine pull question


Reply Closed Thread Share

All times are GMT -5. The time now is 09:03 AM.