Lost turn signal and hazard lights function Failed CPU No. 2?
#1
Rotary Enthusiast
Thread Starter
iTrader: (32)
Lost turn signal and hazard lights function Failed CPU No. 2?
So yesterday I was driving my FD, and part way through the drive I lost turn signal function when operating the turn signals there is nothing, no lights or clicking. Same with the hazards, nothing. Literally one minute they were working, and at the next intersection they were not. I checked the fuse for this circuit, and it is fine.
In looking at the schematic, it looks like the hazards and turn signals are controlled by CPU No. 2 all the T/S and hazard switches do is complete a circuit to CPU No. 2 which then sends the signal to the appropriate lamp. I have read some posts about strange alarm and seat belt light function caused by a failing CPU No. 2, but nothing about nonfunctional turn signals. All the other CPU No. 2 functions seem to be working okay AFAIK, although the key-in ignition open-door chime has always activated for both the drivers side and passenger side doors which is not correct but I just ignored it. I previously modded my CPU No. 2 with a resistor per the forum write up so that it would flash correctly with LED lamps, in case this is relevant.
Are nonfunctional turn signals/flashers (with working seat belt light functions, etc.) likely the result of a failed CPU No. 2? Thought Id ask before I ordered a new part. Thanks for any help with this!
In looking at the schematic, it looks like the hazards and turn signals are controlled by CPU No. 2 all the T/S and hazard switches do is complete a circuit to CPU No. 2 which then sends the signal to the appropriate lamp. I have read some posts about strange alarm and seat belt light function caused by a failing CPU No. 2, but nothing about nonfunctional turn signals. All the other CPU No. 2 functions seem to be working okay AFAIK, although the key-in ignition open-door chime has always activated for both the drivers side and passenger side doors which is not correct but I just ignored it. I previously modded my CPU No. 2 with a resistor per the forum write up so that it would flash correctly with LED lamps, in case this is relevant.
Are nonfunctional turn signals/flashers (with working seat belt light functions, etc.) likely the result of a failed CPU No. 2? Thought Id ask before I ordered a new part. Thanks for any help with this!
#2
So yesterday I was driving my FD, and part way through the drive I lost turn signal function when operating the turn signals there is nothing, no lights or clicking. Same with the hazards, nothing. Literally one minute they were working, and at the next intersection they were not. I checked the fuse for this circuit, and it is fine.
In looking at the schematic, it looks like the hazards and turn signals are controlled by CPU No. 2 all the T/S and hazard switches do is complete a circuit to CPU No. 2 which then sends the signal to the appropriate lamp. I have read some posts about strange alarm and seat belt light function caused by a failing CPU No. 2, but nothing about nonfunctional turn signals. All the other CPU No. 2 functions seem to be working okay AFAIK, although the key-in ignition open-door chime has always activated for both the drivers side and passenger side doors which is not correct but I just ignored it. I previously modded my CPU No. 2 with a resistor per the forum write up so that it would flash correctly with LED lamps, in case this is relevant.
Are nonfunctional turn signals/flashers (with working seat belt light functions, etc.) likely the result of a failed CPU No. 2? Thought Id ask before I ordered a new part. Thanks for any help with this!
In looking at the schematic, it looks like the hazards and turn signals are controlled by CPU No. 2 all the T/S and hazard switches do is complete a circuit to CPU No. 2 which then sends the signal to the appropriate lamp. I have read some posts about strange alarm and seat belt light function caused by a failing CPU No. 2, but nothing about nonfunctional turn signals. All the other CPU No. 2 functions seem to be working okay AFAIK, although the key-in ignition open-door chime has always activated for both the drivers side and passenger side doors which is not correct but I just ignored it. I previously modded my CPU No. 2 with a resistor per the forum write up so that it would flash correctly with LED lamps, in case this is relevant.
Are nonfunctional turn signals/flashers (with working seat belt light functions, etc.) likely the result of a failed CPU No. 2? Thought Id ask before I ordered a new part. Thanks for any help with this!
Thread
Thread Starter
Forum
Replies
Last Post