Interesting Intercooler Piping Set-up
#1
Interesting Intercooler Piping Set-up
Never seen anything like this before, I would think he would get more flow with one larger pipe than three smaller ones. Interesting none the less and thought i would share.
Last edited by purerx7; 11-29-07 at 02:24 PM.
#4
Racecar - Formula 2000
Well, since there are 3 openings in the throttle body, he was probably trying to get more equal flow/pressure to each by dividing them in a straight-flow area, rather than have the air flow hug one wall or the other of a single pipe as it went around the bend near the throttle body.
#6
Senior Member
iTrader: (1)
I think this method may actually reduce the turbulence right at the entrance to the throttle body as each pipe (which now appear to be eqaul length as well) flows the compressed air directly the a particular port on the throttle body. That spells easy smooth flow if you ask me...as opposed to the mass of air going towards the throttle body bouncing on the divider between the ports and causing turbulence right there. I think its a great idea
#7
development
crazy effort for custom-ness.
the twins blow into a collected IC...then a collected outlet splits flow into a primary runner(s) and splits the two secondary runners before being collected in the UIM...once again.
I'd like to see independent twins blow in opposing rotors...like a Vmotor step up. (I.E. front rotor spins turbo 1 and feeds rear rotor that spins turbo 2 which feeds front rotor.)
the twins blow into a collected IC...then a collected outlet splits flow into a primary runner(s) and splits the two secondary runners before being collected in the UIM...once again.
I'd like to see independent twins blow in opposing rotors...like a Vmotor step up. (I.E. front rotor spins turbo 1 and feeds rear rotor that spins turbo 2 which feeds front rotor.)
Trending Topics
#8
Rotary Enthusiast
iTrader: (25)
That's pretty cool and definitely unique.
Have you seen Garfinkle's rich man's nonseq setup dubulup? I think the runners on the manifold are isolated, so similar to how you describe. Aren't some people with custom twin turbo setups also doing this (like howard coleman)?
Have you seen Garfinkle's rich man's nonseq setup dubulup? I think the runners on the manifold are isolated, so similar to how you describe. Aren't some people with custom twin turbo setups also doing this (like howard coleman)?
#10
Senior Member
Join Date: May 2005
Location: Francisco, CA
Posts: 569
Likes: 0
Received 0 Likes
on
0 Posts
I think this method may actually reduce the turbulence right at the entrance to the throttle body as each pipe (which now appear to be eqaul length as well) flows the compressed air directly the a particular port on the throttle body. That spells easy smooth flow if you ask me...as opposed to the mass of air going towards the throttle body bouncing on the divider between the ports and causing turbulence right there. I think its a great idea
#11
2/4 wheel cornering fiend
I think this method may actually reduce the turbulence right at the entrance to the throttle body as each pipe (which now appear to be eqaul length as well) flows the compressed air directly the a particular port on the throttle body. That spells easy smooth flow if you ask me...as opposed to the mass of air going towards the throttle body bouncing on the divider between the ports and causing turbulence right there. I think its a great idea
The second part of airflow 101 he forgot was that the stock elbow actually slows down the airflow as it approaches the TB because it expands as it reaches that point, drastically cutting down on any turbulence created at surfaces outside the throttle body intakes.
While there's other aspects of the car that allow room for alternative thought, the basic engine setup wasn't exactly arrived at by chance. Attempting to outthink the Mazda engineers on this aspect of the design without thinking it through is an exercise in futility.
#12
Cheap Bastard
iTrader: (2)
I think it is restrictive. Lets do the math:
Looks like a 3" pipe leaving the intercooler. That would leave an opening of about 7 square inches. The 3 pipes coming off the big pipe appear to be about 1 1/2 inches. That would make for a total of about 5.3 square inches. If my estimates are correct, those smaller pipes are reducing flow by about 25%.
Looks like a 3" pipe leaving the intercooler. That would leave an opening of about 7 square inches. The 3 pipes coming off the big pipe appear to be about 1 1/2 inches. That would make for a total of about 5.3 square inches. If my estimates are correct, those smaller pipes are reducing flow by about 25%.
Thread
Thread Starter
Forum
Replies
Last Post