Identifying the combination switch/ ignition switch for Painless Wiring kit install
#1
Identifying the combination switch/ ignition switch for Painless Wiring kit install
Hey guys i am almost done with the install on my FD. I am using Painless Performance race car harness 21 circuit Part #50002.
What I need help on is identifying each of the wires on the combination switch and ignition switch. I cut the pig tails off the dash harness so it can be a direct connection to the painless. Now the painless kit has the wires already labeled so all I have to do is mate it to the designated wire on the clip.
I am asking you to help me label what wire goes to what from there I can use what i need. Heres were it simplifies everything on my set up. I have the z-wiring diagram/ILUVMYRX7 diagrams and lets just say they are hard to look at. Please chime in i will update the diagram until its complete.
---NO pop up lights or oem lighting system. I am using HIDS on my sleek lights. all i need is on and off on the switch.
---1 speed on my wipers again it will only utilize the on and off the switch
--- NO AC/NO POWERSTEERING/NO HEATER/NO OEM WIRING AT ALL
---Haltech/Iq3 is managing everything from the fuel pump to fans. the dash cluster is also haltech.
Combination switch X-04
-----TOP ROW----
L/R
G/Y
B/Y
Y
G
B
L/W
L/B
L/O
B
L/Y
----BOTTOM ROW----
GY/R
W/L
R/Y
R/W
R
W/G
L/G
Y/R
B
O
Ignition Swicth X-03
------------TOP ROW----------
B/L- Start wire to starter
B/G- 12+
B/Y -IGNITION 2
-----------BOTTOM ROW---------
L
L/B- 12+
B/W-
THESE ARE OEM WIRES OFF THE COMBINATION SWITCH I NEED.
Left turn signal
Right turn signal
Parking lights
Low beams
Wipers -front only -no washer
What I need help on is identifying each of the wires on the combination switch and ignition switch. I cut the pig tails off the dash harness so it can be a direct connection to the painless. Now the painless kit has the wires already labeled so all I have to do is mate it to the designated wire on the clip.
I am asking you to help me label what wire goes to what from there I can use what i need. Heres were it simplifies everything on my set up. I have the z-wiring diagram/ILUVMYRX7 diagrams and lets just say they are hard to look at. Please chime in i will update the diagram until its complete.
---NO pop up lights or oem lighting system. I am using HIDS on my sleek lights. all i need is on and off on the switch.
---1 speed on my wipers again it will only utilize the on and off the switch
--- NO AC/NO POWERSTEERING/NO HEATER/NO OEM WIRING AT ALL
---Haltech/Iq3 is managing everything from the fuel pump to fans. the dash cluster is also haltech.
Combination switch X-04
-----TOP ROW----
L/R
G/Y
B/Y
Y
G
B
L/W
L/B
L/O
B
L/Y
----BOTTOM ROW----
GY/R
W/L
R/Y
R/W
R
W/G
L/G
Y/R
B
O
Ignition Swicth X-03
------------TOP ROW----------
B/L- Start wire to starter
B/G- 12+
B/Y -IGNITION 2
-----------BOTTOM ROW---------
L
L/B- 12+
B/W-
THESE ARE OEM WIRES OFF THE COMBINATION SWITCH I NEED.
Left turn signal
Right turn signal
Parking lights
Low beams
Wipers -front only -no washer
Last edited by Alex Rodriguez; 08-04-14 at 08:48 PM.
Thread
Thread Starter
Forum
Replies
Last Post