How to maximize pre-spool ?
#1
Full Member
Thread Starter
Join Date: Oct 2003
Location: Scottsdale, Arizona
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
How to maximize pre-spool ?
I'm trying to fix my low transition boost. I've got a 10-6-10 pattern with the PFS on 10. I've attached my boost gauge at the back of the Y pipe to measure pre spool. I'm only getting to about 5 psi (at 4500) on the pre-spool with my HD valve all the way open. I've even removed the valve and disconnected the pc solenoid (This cuts the primary down to 7psi). I'm still only getting about 7 psi of pre-spool. What could be causing this ? I should get a big spike, right ?
#2
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Turbo Precontrol valve is the one you need to adjust. Assuming everything else is working properly......
This is how I eliminated my dip at 4500rpms. Just gotta open it up to allow more exdhaust to get to the 2nd turbo before transition.
This is how I eliminated my dip at 4500rpms. Just gotta open it up to allow more exdhaust to get to the 2nd turbo before transition.
#3
Cheap Bastard
iTrader: (2)
The HD controllers don't work very well on the prespool. It can be nearly impossible to get them working properly together. I believe the extra length of the hose causes the problem.
I had a prespool controller on my car and tried (for a month) to get it working right. Eventually, I gave up and reinstalled the stock hose (with the pills). My boost pattern went back to 12-8-12. I think the ECU tries to keep prespool at a stock level of around 8, regardless of where the primary spools.
I had a prespool controller on my car and tried (for a month) to get it working right. Eventually, I gave up and reinstalled the stock hose (with the pills). My boost pattern went back to 12-8-12. I think the ECU tries to keep prespool at a stock level of around 8, regardless of where the primary spools.
#5
Rotary Freak
Join Date: Dec 2002
Location: Slovenia, Europe
Posts: 2,522
Likes: 0
Received 0 Likes
on
0 Posts
Have same issue as adam. Cant get to 12-10-12 pattern... and am stuck with 12-8-12. There is quite some powerloss at transition because of it (by the feel of the seat of the pants).
#6
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by adam c
....I had a prespool controller on my car and tried (for a month) to get it working right. Eventually, I gave up and reinstalled the stock hose (with the pills). My boost pattern went back to 12-8-12. I think the ECU tries to keep prespool at a stock level of around 8, regardless of where the primary spools.
....I had a prespool controller on my car and tried (for a month) to get it working right. Eventually, I gave up and reinstalled the stock hose (with the pills). My boost pattern went back to 12-8-12. I think the ECU tries to keep prespool at a stock level of around 8, regardless of where the primary spools.
The rod end of the actuator has threads where it connects to the flap which allows you to adjust its position.
#7
Cheap Bastard
iTrader: (2)
Originally posted by Flybye
I MANUALLY adjusted the flap.
The rod end of the actuator has threads where it connects to the flap which allows you to adjust its position.
I MANUALLY adjusted the flap.
The rod end of the actuator has threads where it connects to the flap which allows you to adjust its position.
Thanks, Adam
Trending Topics
#8
Rotary Enthusiast
Join Date: Dec 2001
Location: Sunnyvale, CA
Posts: 1,252
Likes: 0
Received 0 Likes
on
0 Posts
I found that the prespool HD valve, needs to close as much as only 1/2 turn. This will give more flow to the secondary prespool. If you close it, you will get spike.
#10
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
https://www.rx7club.com/showthread.p...ool+adjustment
This thread should help.
When I get home, I'll post a diagram of the flap system so that you can easily visualize it.
This thread should help.
When I get home, I'll post a diagram of the flap system so that you can easily visualize it.
#11
Full Member
Thread Starter
Join Date: Oct 2003
Location: Scottsdale, Arizona
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
Well, I just wired the precontrol open and the charge control closed. Still only 7 psi on the secondary before transition. Could the precontrol be clogged ? Anyone know how much secondary boost should be generated by a fully open precontrol ?
#14
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Ok quick summary of what does what here....
As per the factory ECU, the Prespooler acts as a mini wastegate for the primary turbo. Wastegate stays closed and the prespooler pretty much regulates primary boost. As you can see, the more the prespool rod pushes out, the more it opens the flap to allow exhaust to get to the 2nd turbo.
During prespool, the charge relief valve vents any boost from the 2nd turbo before 4500 rpms. At 4500rpms, the prespooler opens up all the way. Also the Turbo control actuator is still closed not allowing any exhaust to get to the 2nd turbo.
Now here's where it gets tricky....
The charge control actuator relies on boost from both sides of the charge control valve in order to open. The Charge control solenoid is what allows this extra pressure to reach the other side of the actuator. Once that little sucker sees boost pressure almost the same on both sides of the charge control valve, it opens the valve.
The turbo control actuator is the big bitch that causes the most headaches. That **** needs vaccum AND boost to operate properly. Which is why we have a vacuum and pressure tank. The solenoids regulate how much of all this gets sent to the actuator.
Now do you understand what you are doing? Wiring the charge control closed you are basically putting a wall infront of the 2nd turbo. Wiring the precontrol open still might not be enough to open the flap ALL the way since you still may be able to adjust the flap at the rod by turning it out a bit so that the door opens up more. Look at the diagram and make sure you didn't accidentally wire the prespool flap closed
I haven't been down there in a while, but I think the Turbo control can also be adjusted.
Yes, our exhaust manifold is an extreme bottleneck
#15
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by adam c
..... I think the ECU tries to keep prespool at a stock level of around 8, regardless of where the primary spools.
..... I think the ECU tries to keep prespool at a stock level of around 8, regardless of where the primary spools.
It takes a while to adjust the flaps to a point where you will be happy. Adjust.....run....adjust....run.........adjust.... ext.
You have to adjust it so that you get minimal drop at 4500rpm and still get max boost on the primary meaning getting full boost (12psi) by around 3000rpm. My 4500rpm drop is hardly 1/2 a pound. I mean it happens so fast you almost don't even see the needle move
#17
Full Member
Thread Starter
Join Date: Oct 2003
Location: Scottsdale, Arizona
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
Well, my CRV closes at 3500. Others have observed this as well. This makes sense, because you wouldn't see any boost pressure at the back of the Y pipe if the CRV was open. I popped the PS actuator rod off, so I know I had the prespool all the way open. Also the rod is actually set up a little long (supposed to overlap, then you pull it to attach). I'm looking at pre transition boost, so I wired the charge control just to make sure it wasn't opening prematurely. I also read in the thread you posted that with the rod too long (too much ps) you should only see 5 psi on the primary. So I think maybe I need to take my precontrol gate apart. Turbo control seems good to me. The spool up from 6 to 10 is pretty fast.
#19
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Before you start taking things apart, remember there is still a solenoid for the charge relief, charge control, and prespool control.
A line causing a leak or even a bad solenoid could still be the problem. The precontrol flap doesnt simply clog up. At least I've never seen one clogged up
For example, a bad hose with a leak between the precontrol valve and the precontrol actuator would cause not enough boost to get to that actuator causing it not to open up enough or at all. Same thing with the charge control. The flap may be opening up TOO slowly or may be sticking.
Non seq is for the sissys
Besides, I've known several guys who went non seq and they regreted it. One of them ended up going to a small single and the other went back to sequential
The Home Depot valves sometimes work. They didn't work for me. Besides, you do this right and it will be one less valve in the engine compartment. They won't work at all if you have something wrong with the control system.
A line causing a leak or even a bad solenoid could still be the problem. The precontrol flap doesnt simply clog up. At least I've never seen one clogged up
For example, a bad hose with a leak between the precontrol valve and the precontrol actuator would cause not enough boost to get to that actuator causing it not to open up enough or at all. Same thing with the charge control. The flap may be opening up TOO slowly or may be sticking.
Non seq is for the sissys
Besides, I've known several guys who went non seq and they regreted it. One of them ended up going to a small single and the other went back to sequential
The Home Depot valves sometimes work. They didn't work for me. Besides, you do this right and it will be one less valve in the engine compartment. They won't work at all if you have something wrong with the control system.
#21
Full Member
Thread Starter
Join Date: Oct 2003
Location: Scottsdale, Arizona
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
I'm hooked on the low end/part throttle response of sequential. I wired the pc and cc and blocked the crv. So the solenoids weren't an issue. This gave me the situation for max prespool: cc closed, crv closed, ps all the way open. (I also tried it with the crv normal - open till 3500). I am going to try lengthening the tca rod to see if that helps. I suspect, though that the key to a good transition is seeing 8 (or 10) psi at the back of the Y pipe, then quickly spooling to 10 (or 12) after the transition. Anyone with a spike or even transition know what they get at 4400 on that line ?
#22
Senior Member
Originally posted by Fred Sickert
Well, my CRV closes at 3500. Others have observed this as well.
Well, my CRV closes at 3500. Others have observed this as well.
-pete
#24
It's never fast enough...
Join Date: Feb 2001
Location: Miami - Given 1st place as the POOREST city in the US as per the federal government
Posts: 3,760
Likes: 0
Received 3 Likes
on
3 Posts
Originally posted by Fred Sickert
..... I am going to try lengthening the tca rod to see if that helps. I suspect, though that the key to a good transition is seeing 8 (or 10) psi at the back of the Y pipe, then quickly spooling to 10 (or 12) after the transition......
..... I am going to try lengthening the tca rod to see if that helps. I suspect, though that the key to a good transition is seeing 8 (or 10) psi at the back of the Y pipe, then quickly spooling to 10 (or 12) after the transition......
Keeping the charge control valve open, you shouldn't feel anything either. The reason we all get a dip or spike at 4500 rpm is because when that little valve open, if the 2nd turbo is creating more boost than the 1st, that will cause the spike. If it has less boost than the 1st, that is what causes the dip.
#25
Full Member
Thread Starter
Join Date: Oct 2003
Location: Scottsdale, Arizona
Posts: 177
Likes: 0
Received 0 Likes
on
0 Posts
I've got the non-seq switch. I get full boost by about 4500. I've been thinking about the charge control. It's supposed to open when secondary boost is more than primary (Either side of the diaphram). But there is also spring pressure pushing it open, so it wants to open, even if the secondary is lower. With pc all the way on the transition is 7-7-8. Its hard to tell exactly where the drop to 6 is, I guess I need datalogging to really tell. I'm going to try a much shorter line on the pc and see if that makes a difference.