3rd Generation Specific (1993-2002) 1993-2002 Discussion including performance modifications and Technical Support Sections.
Sponsored by:

Help/Code 11 & glowing ex-manifold? has anyone ecounter with this code before?

Thread Tools
 
Search this Thread
 
Old 05-05-05, 08:56 PM
  #1  
Rotary Freak

Thread Starter
iTrader: (22)
 
Rx7aholic's Avatar
 
Join Date: Feb 2001
Location: Morris Plains, NJ USA
Posts: 1,922
Received 2 Likes on 2 Posts
Unhappy Help/Code 11 & glowing ex-manifold? has anyone ecounter with this code before?

Hey over the winter months I reaplce my omp lines, and FPR with an aftermarket type {paxton} same as sx, anyway car startup fine and warmup perfect and shows no sign of hestation or alot of fuel is dumping into engine. Anyway I notice the glowing exhaust and deceide to plug the diagnostic tester and code 11 pop out? According to the book it's the Idle cam and ISC but for those smystoms the car suppose to shut off unexpected or rough idle? Which the car show no sign's of either? Can anyone help me with this weir problem thanks alot, khris
Old 05-06-05, 03:51 AM
  #2  
Wankel Shmankel

 
POS7's Avatar
 
Join Date: Mar 2005
Location: Oahu (Hawaii)
Posts: 627
Likes: 0
Received 0 Likes on 0 Posts
According to rob robinette (sp?) website, code 11 is the IAT sensor. NOt sure if its the one under the UIM. There's two listed. NOt sure how this would be related to a glowing exhaust manifold. Maybe the IAT is faulty and reading a funny temp, so a lot of fuel is dumping into the motor? Clogged cat causing the exhaust manifold to heat?

not sure about this one, sorry

10 Intake air thermosensor (AFM)
11 Intake air thermosensor (engine)
Old 05-06-05, 06:41 AM
  #3  
Full Member

 
Rotarytard's Avatar
 
Join Date: Mar 2004
Location: boston
Posts: 231
Likes: 0
Received 0 Likes on 0 Posts
the intake air thermosensor is the blue sensor underneath the upper intake manifold. there are like 3 connectors that look that same. one time i connected the wrong one to the sensor and got the code.

also try resetting the ecu.
Old 05-06-05, 08:44 AM
  #4  
Rotary Freak

iTrader: (8)
 
Cgotto6's Avatar
 
Join Date: Nov 2003
Location: Bothell, Washington
Posts: 1,893
Received 2 Likes on 2 Posts
Make sure the sensor is grounded out. The ground for it is on the rear hoist hook, bottom bolt. I left this ground off, and I pulled this code. My exhaust was glowing with this as well. It sets the ECU into safe mode, and says the air temp is always 60 some degrees, so it runs rich as ****. Good luck.
Old 05-06-05, 09:01 AM
  #5  
Full Member

 
Addict's Avatar
 
Join Date: May 2003
Location: Aurora IL
Posts: 134
Likes: 0
Received 1 Like on 1 Post
When I was throwing code11 I changed the sensor on the underside of the UIM. Never saw the code again. Also ran better. It wasn't hesitating before, but when I floored it it just wouldn't accelerate the way it should(ie running rich).

I was also getting a glowing downpipe after startup, but I thought that went away with something else, not the sensor replacement, but it could have been related.
Old 05-06-05, 11:45 AM
  #6  
Senior Member

 
FDeez's Avatar
 
Join Date: Jul 2001
Location: Oakland, CA
Posts: 735
Likes: 0
Received 1 Like on 1 Post
Glowing exhaust pipes mean that you're running pretty damn rich. A faulty Air intake temp sensor would cause your car to run rich as a safety measure. Mine did this too, however, when my air intake temp sensor went out, my car started bucking like crazy. Replace the air intake temp sensor and see if that solves your problems. I believe the sensor was ~$40 from Malloy Mazda.
Old 05-06-05, 09:33 PM
  #7  
Rotary Freak

Thread Starter
iTrader: (22)
 
Rx7aholic's Avatar
 
Join Date: Feb 2001
Location: Morris Plains, NJ USA
Posts: 1,922
Received 2 Likes on 2 Posts
Ok sound like I cross the connectors with the intake air thermosensor, I will check it out tomorrow. thanks alot, khris
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
SakeBomb Garage
SakeBomb Garage
9
05-11-20 10:04 AM
SakeBomb Garage
Group Buy & Product Dev. FD RX-7
8
10-09-15 10:05 PM
spokanerxdude
Megasquirt Forum
3
10-06-15 12:28 PM
iamsisyphus
2nd Generation Specific (1986-1992)
6
09-27-15 01:42 PM



Quick Reply: Help/Code 11 & glowing ex-manifold? has anyone ecounter with this code before?



All times are GMT -5. The time now is 11:30 PM.