BNR Stage 3 - #'s don't add up.
#1
BNR Stage 3 - #'s don't add up.
Last year around this time, I had my car tuned and dyno'd to 15PSI on some ported NS twins and I netted ~340RWP from the car(depending on who's correction #s you factor in). Car has 43K miles on it now, still orignal motor so it still has stock ports etc. I was failry happy with the power #'s but my M2 Medium SMIC was simply heat soaking waaay to much when I started boosting. I wanted to modify a few more things and decided to get the thick Apexi GT Spec FMIC. I also purcahsed ported UIM and LIM for the car, replaced the old fuel system with the CJ Motorsports Rails and ID fuel injectors.
In the midst of all this i bought a set of BNR stage3s from Rx7aholic and decided to go ahead and upgrade the twins with better more efficient twins vs going single just yet.
My results were a gain in ~12hp Uncorrected to the wheels from last year to this year, and this is with much better IATs, and more controlled Water temps vs last year. UNcorrected last year I was at 310hp, this year uncorrected I was at 321 and I was running a bit more boost to 17psi. I had plenty of fuel, but no water or meth yet to reduce knock. So here is what I am scratching my head on: Are the stock ports really that restrictive? I saw a friends car with Stock Ports and a GT40 on e85 hit 440RWHP (before a stuck corner seal stopped his tuning session). Granted E85 helps that knock control, but that is a huge difference.
Here is the setup. I would really appreciate any insight you guys could provide. Mod list:
RB dual exaust (potentially restrictive component)
Magnflow Resonated Midpipe
3"downpipe
BNR stage 3 Twins - NS
RichMans ported manifod (gates removed etc)
Ported and Polished LIM & UIM
Greddy Elbow
Apexi GT Spec FMIC
Efini Y pipe, welded shut for after marked BOV
Apexi Cold Air Intake
HKS Ignition Enhancer
CJ Motorsports Fuel rails
ID 725 Primaries 2200 secondaries
PFC
I still have AC/PS and cruise as well .
No cooling issues, ducting is working really well. Just for some reason, couldn't safely get the power past 321 uncorrected off the superflow dyno.
Thoughts? Car runs strong. I guess I could check compression again as this is still the stock motor at 43K miles, but I have yet to have any issues with warm/cold start etc.
Thanks for any other opinions. I will post dyno charts soon if you want to compare.
In the midst of all this i bought a set of BNR stage3s from Rx7aholic and decided to go ahead and upgrade the twins with better more efficient twins vs going single just yet.
My results were a gain in ~12hp Uncorrected to the wheels from last year to this year, and this is with much better IATs, and more controlled Water temps vs last year. UNcorrected last year I was at 310hp, this year uncorrected I was at 321 and I was running a bit more boost to 17psi. I had plenty of fuel, but no water or meth yet to reduce knock. So here is what I am scratching my head on: Are the stock ports really that restrictive? I saw a friends car with Stock Ports and a GT40 on e85 hit 440RWHP (before a stuck corner seal stopped his tuning session). Granted E85 helps that knock control, but that is a huge difference.
Here is the setup. I would really appreciate any insight you guys could provide. Mod list:
RB dual exaust (potentially restrictive component)
Magnflow Resonated Midpipe
3"downpipe
BNR stage 3 Twins - NS
RichMans ported manifod (gates removed etc)
Ported and Polished LIM & UIM
Greddy Elbow
Apexi GT Spec FMIC
Efini Y pipe, welded shut for after marked BOV
Apexi Cold Air Intake
HKS Ignition Enhancer
CJ Motorsports Fuel rails
ID 725 Primaries 2200 secondaries
PFC
I still have AC/PS and cruise as well .
No cooling issues, ducting is working really well. Just for some reason, couldn't safely get the power past 321 uncorrected off the superflow dyno.
Thoughts? Car runs strong. I guess I could check compression again as this is still the stock motor at 43K miles, but I have yet to have any issues with warm/cold start etc.
Thanks for any other opinions. I will post dyno charts soon if you want to compare.
#4
r074r'/ |\|00B
iTrader: (14)
Join Date: Jan 2002
Location: KC, KS
Posts: 922
Likes: 0
Received 0 Likes
on
0 Posts
Sorry to hear about your disappointment Dan. I was hoping to make it up there this year but school has slowed me down way too much. Only 1 more month to go and I'm done for good. How do you like the 725/2000 injectors? That's the combo I'm looking at running, I've already got the 725's but nothing installed yet. I might have to bug you later on about how you have everything plumbed.
#5
The injectors are great. The CJ MotorSports Fuelrails are a snap to install, and they will give you great support. They also modified the spacers on the 48mm injectors for the primaries so you wont need all of the extensions for 60mm injector spacing we are used to. It all fits with plenty of clearance and it provides great delivery. IDs are great fuel injectors thus far at least.....
Now if I can just get this power thing figured out.
Now if I can just get this power thing figured out.
Trending Topics
#10
rotary sensei
iTrader: (5)
Join Date: Mar 2001
Location: Virginia
Posts: 2,312
Likes: 0
Received 0 Likes
on
0 Posts
Read through this thread, it should answer your questions.
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/bnr-stage-3-turbos-966671/
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/bnr-stage-3-turbos-966671/
#12
Read through this thread, it should answer your questions.
https://www.rx7club.com/showthread.php?t=966671
https://www.rx7club.com/showthread.php?t=966671
#14
Yes they are Ver 1 of the BNRs, but still worthy of good power #s... I think it simply boils down to stock ports, and no AI means lower power. Add improvements to one or both, and a change can be seen... Perhaps it may be time to send the motor out for porting and enhancements before it pops!!
#16
So Tom, I have been following your threads, and granted I prolly need to go back and look at everything again, but your motor was streetported ... ah your sig actually states that, so I guess it goes back to my original question. I should be able to hit 375 based on my mods all day on pump gas, so what gives? Even Stage 1 BNRs are capable of this. I just don't understand the 30+ HP delta. And I agree, just spraying for Knock reduction will take out power, but it should allow for more boost and less timing, allowing for more power, Right?
Now I will say, the turbine sound of the BNRs... AWESOME
Now I will say, the turbine sound of the BNRs... AWESOME
#17
Rotary Enthusiast
iTrader: (5)
I'm not sure but you may just need more boost, and AI would be a good idea to have. I did make 368 hp with the stock engine with 21 psi peak and non seq turbos. On that day it also made only 313 hp with 16 psi. The boost makes a big difference. https://www.rx7club.com/showthread.p...&highlight=368
#18
Turbo Lover
iTrader: (6)
Join Date: Feb 2003
Location: Cleveland
Posts: 783
Likes: 0
Received 0 Likes
on
0 Posts
Boost makes all the difference with these turbos, that and water/meth. I'm sure your stock ports are hurting you as well but it shouldn't make that crazy of a difference. If I were you the first thing I'd check is compression, as usually a post about "why didn't I make that much power" is quickly followed by a "my engine blew" post.
I guess it could be the dyno, but even I did my numbers on a Mustang dyno. Unless it was a Dyno Dynamics dyno I can't imagine your power being that much off.
Only other thing I can think of, and I'm basically taking the lords name in vane by saying this in the rx7 world, but every time I hear about a Steve Kan tuned car the numbers always seem to be underwhelming.
I guess it could be the dyno, but even I did my numbers on a Mustang dyno. Unless it was a Dyno Dynamics dyno I can't imagine your power being that much off.
Only other thing I can think of, and I'm basically taking the lords name in vane by saying this in the rx7 world, but every time I hear about a Steve Kan tuned car the numbers always seem to be underwhelming.
#19
Senior Member
iTrader: (5)
[QUOTE=
Only other thing I can think of, and I'm basically taking the lords name in vane by saying this in the rx7 world, but every time I hear about a Steve Kan tuned car the numbers always seem to be underwhelming.[/QUOTE]
But you also don't hear Steve tuned my car and now I need a motor. I think by default he tunes conserative to protect against all the variable the car will encounter off the dyno. Don's numbers were of a superflow dyno. I know the dyno Don tuned on seems conserative against other dynos I have been on.
Only other thing I can think of, and I'm basically taking the lords name in vane by saying this in the rx7 world, but every time I hear about a Steve Kan tuned car the numbers always seem to be underwhelming.[/QUOTE]
But you also don't hear Steve tuned my car and now I need a motor. I think by default he tunes conserative to protect against all the variable the car will encounter off the dyno. Don's numbers were of a superflow dyno. I know the dyno Don tuned on seems conserative against other dynos I have been on.
#20
I will not discredit steve's tuning abilities at all. There is a reason why this car has 43k miles still on the stock motor and running strong. Steve has tuned this car 3+ times over its life span and this thing keeps on taking a beating. I looked up the superflow dyno... Rumor states its a stingy one for pulling out big #'s. Maybe I am just not setting my expectations right.
Time to take it to the track and let the machine do the talking.
Time to take it to the track and let the machine do the talking.
#21
rotary sensei
iTrader: (5)
Join Date: Mar 2001
Location: Virginia
Posts: 2,312
Likes: 0
Received 0 Likes
on
0 Posts
So Tom, I have been following your threads, and granted I prolly need to go back and look at everything again, but your motor was streetported ... ah your sig actually states that, so I guess it goes back to my original question. I should be able to hit 375 based on my mods all day on pump gas, so what gives? Even Stage 1 BNRs are capable of this. I just don't understand the 30+ HP delta. And I agree, just spraying for Knock reduction will take out power, but it should allow for more boost and less timing, allowing for more power, Right?
Now I will say, the turbine sound of the BNRs... AWESOME
Now I will say, the turbine sound of the BNRs... AWESOME
As far as the water meth we never ran the car without it so I can't help you there. The tune can make a huge difference, I cannot over emphasize that enough.
#23
I may just go ahead and get the motor ported and run some AI this next coming winter. I am not trying to set any records on stock motor life, but as Rich once advised, it is a LOT cheaper to port and improve a currently solid motor than to wait til something lets go.
On the RB duals... I am torn. The car is subtlely loud right now - or as one of my friends put it, I have the Cadillac of RX7s (PS, AC, Cruise, working Radio, and it doesn't reek of gas and you can have a conversation as you drive down the road, - yet it pulls like a bat out of hell). I know they are restricting, but how much is the question...
So net result, ~350 HP is a nice safe point @17PSI on stock ports and no AI on pump gas. I guess at the end of the day it is just #s. this car is a blast to drive.