Aem 30-0300 x-series wind bad. HELP

Reply Subscribe

Thread Tools

Search this Thread

Feb 21, 2019 | 03:53 PM

existanzrx7

Thread Starter

Just Boosting

iTrader: (8)

Joined: Mar 2004

Posts: 1,125

Likes: 7

From: Chy-Town

Aem 30-0300 x-series wind bad. HELP

Ok first off I did search but can only find how to wire an older Aem gauge. What I need to know, is how to wire this gauge to work with my Datalogit/Power Fc. Which wires do I connect to my Datalogit? Thanks

Last edited by existanzrx7; Feb 21, 2019 at 03:59 PM.

Feb 21, 2019 | 06:42 PM

cr-rex

half ass 2 or whole ass 1

iTrader: (114)

Joined: Nov 2011

Posts: 3,425

Likes: 489

From: okinawa to tampa

The white and brown wires go to the datalogit. They're your 0-5v and gnd.

Feb 21, 2019 | 06:49 PM

existanzrx7

Thread Starter

Just Boosting

iTrader: (8)

Joined: Mar 2004

Posts: 1,125

Likes: 7

From: Chy-Town

Quote:

Originally Posted by cr-rex

The white and brown wires go to the datalogit. They're your 0-5v and gnd.

The Datalogit has several connections. Any idea to which connection do the White and Brown wire hook to on the Datalogit? Thanks bud.

Feb 21, 2019 | 07:06 PM

existanzrx7

Thread Starter

Just Boosting

iTrader: (8)

Joined: Mar 2004

Posts: 1,125

Likes: 7

From: Chy-Town

Found a pic that shows all the connections pretty clearly. So this should help to anyone like my self that don’t have the Datalogit on hand. So help me out guys thanks.

Feb 21, 2019 | 09:50 PM

cr-rex

half ass 2 or whole ass 1

iTrader: (114)

Joined: Nov 2011

Posts: 3,425

Likes: 489

From: okinawa to tampa

It's labeled on the datalogit. AN is 0-5v input and SW is your 0v/gnd.

Feb 21, 2019 | 11:36 PM

existanzrx7

Thread Starter

Just Boosting

iTrader: (8)

Joined: Mar 2004

Posts: 1,125

Likes: 7

From: Chy-Town

Quote:

Originally Posted by cr-rex

It's labeled on the datalogit. AN is 0-5v input and SW is your 0v/gnd.

Thanks bud I think I got it. But what do you mean with sw? What does that stand for. There are no sw markings on the Datalogit except for An1 threw 8 and then one spot with 0V.

Last edited by existanzrx7; Feb 21, 2019 at 11:39 PM.

Feb 22, 2019 | 12:01 AM

cr-rex

half ass 2 or whole ass 1

iTrader: (114)

Joined: Nov 2011

Posts: 3,425

Likes: 489

From: okinawa to tampa

I have the beige datalogit and 1-4 is AN and 6-8 are SW with the 1 0v at the top. I'm guessing it's all the same since the datalogit software only lists AN

Trending Topics

Ttt steering rack thoughts

13

526
Engine o ring failure?

11

333
FrankenRex Will Rise: stuffing a GSL-SE into a'79 SA

309

31.8k
RX-7 SA 1979 - European - Aurora White "ETHEREAL"

7

226
6k ignition break up and tach goes wild simultaneously no matter the...

10

340

Feb 22, 2019 | 09:15 AM

DaleClark

RX-7 Bad Ass

iTrader: (56)

Joined: Jan 2002

Posts: 15,622

Likes: 2,725

From: Pensacola, FL

Innovate has an excellent how-to showing how to set up a Wideband with the Datalogit. It applies to your scenario, all widebands have the same 0-5v output for a signal.

https://www.innovatemotorsports.com/...c_tutorial.php

Dale

Feb 23, 2019 | 12:54 AM

scotty305

~17 MPG

iTrader: (2)

Joined: Jan 2004

Posts: 3,478

Likes: 334

From: Bend, OR

That's a really well-written guide, but the voltage-to-AFR for that AEM 30-0300 wideband is different than the numbers shown in the example. In step 3 (Configuring FC Edit to read the Analog Output), use 0.50 Volts = 8.50 AFR and 4.50 Volts = 18.00 AFR.

Mar 3, 2019 | 09:00 AM

#10

mecman

Senior Member

iTrader: (12)

Joined: Jun 2001

Posts: 679

Likes: 24

From: Chicago, IL, USA

This is a good thread. I currently have a narrow band connected to my Power FC.
How does one install a wideband using a Power FC without the datalogit?