replaced broken rear wheel stud
#1
Lives on the Forum
Thread Starter
replaced broken rear wheel stud
Let me start off by saying if you ever break a rear wheel stud, it's a complete bitch. Here is what it took to replace mine:
new stud $.99 (I went ahead and replaced all 5 though, didn't want to risk it)
35mm socket for axle nut $15
replacement axle nut from Mazda $7
new wheel bearing $85
machine shop service $90
So here's how it goes. You can't remove the studs without pressing out the spindle. So you break the axle nut loose (I had to use a 3 foot pipe on my cheater bar to get it loose), remove the caliper and rotor and then hammer the axle out of the spindle. I couldn't get the axle to come loose from the spindle. Beat it with hammer. Beat it with axe. No go. So since I was going to the machine shop anyway I just pulled the whole damn axle from the tripot joint and took the whole axle/wheel hub/spindle assembly in. They heated the spindle and were finally able to press the axle out of the spindle (I should have thought of heat, but forgot). Then you press the spindle out; this destroys the wheel bearing because the inner race stays stuck to the spindle. Then you grind and chisel the race off the spindle. Then you press the old studs out and the new ones in. Then you press in the new wheel bearing. Then you press in the spindle. Then you reassemble car.
Is that friggin nuts or what? I couldn't believe it was so much work and money. Took me less than an hour to get everything off; could have done it in 30 minutes if I hadn't wasted so much time trying to beat the axle out. Once I came home it went together in about 30 minutes. But I just spent over $200 to replace a damned wheel stud.
The moral of the story is to properly torque your wheels religiously. My stud actually broke taking a nut OFF; it cracked right in the middle at the base of the lug nut. My only guess is it had been stressed from overtightening in the past. Make sure the tire guys don't overtorque your lugs!!!!
new stud $.99 (I went ahead and replaced all 5 though, didn't want to risk it)
35mm socket for axle nut $15
replacement axle nut from Mazda $7
new wheel bearing $85
machine shop service $90
So here's how it goes. You can't remove the studs without pressing out the spindle. So you break the axle nut loose (I had to use a 3 foot pipe on my cheater bar to get it loose), remove the caliper and rotor and then hammer the axle out of the spindle. I couldn't get the axle to come loose from the spindle. Beat it with hammer. Beat it with axe. No go. So since I was going to the machine shop anyway I just pulled the whole damn axle from the tripot joint and took the whole axle/wheel hub/spindle assembly in. They heated the spindle and were finally able to press the axle out of the spindle (I should have thought of heat, but forgot). Then you press the spindle out; this destroys the wheel bearing because the inner race stays stuck to the spindle. Then you grind and chisel the race off the spindle. Then you press the old studs out and the new ones in. Then you press in the new wheel bearing. Then you press in the spindle. Then you reassemble car.
Is that friggin nuts or what? I couldn't believe it was so much work and money. Took me less than an hour to get everything off; could have done it in 30 minutes if I hadn't wasted so much time trying to beat the axle out. Once I came home it went together in about 30 minutes. But I just spent over $200 to replace a damned wheel stud.
The moral of the story is to properly torque your wheels religiously. My stud actually broke taking a nut OFF; it cracked right in the middle at the base of the lug nut. My only guess is it had been stressed from overtightening in the past. Make sure the tire guys don't overtorque your lugs!!!!
#2
Full Member
Join Date: Feb 2001
Location: Columbus,OHIO
Posts: 223
Likes: 0
Received 0 Likes
on
0 Posts
I'm one of those tire guys you're talking about. I work at Discount Tire and we're always breaking studs. A couple $$ for a new stud and about $20 and sears or someone will replace it for you. I love working there.....nothing but air tools, torque wrenches, badass tires....ahh....its heaven.
#5
DamonB:
Yep, a rust and heat seized axle is a pain to remove. I had a similar experience once when I changed out a bad rear bearing. In my case, lots of PB blaster and the help of a 5 LB brass hammer did the trick. Just a tip: you may want to lubricate the axle with antiseize, to prevent it from seizing again.
Ikestaa:
The bearing is a sealed bearing, so there is no need to pack it with grease.
Yep, a rust and heat seized axle is a pain to remove. I had a similar experience once when I changed out a bad rear bearing. In my case, lots of PB blaster and the help of a 5 LB brass hammer did the trick. Just a tip: you may want to lubricate the axle with antiseize, to prevent it from seizing again.
Ikestaa:
The bearing is a sealed bearing, so there is no need to pack it with grease.
#6
Lives on the Forum
Thread Starter
Originally Posted by worfvi
Just a tip: you may want to lubricate the axle with antiseize, to prevent it from seizing again.
Trending Topics
#9
Bridgeport Anyone??
Exact same situation happened to me Damonb, only we had to use a shop press to get my axle out of the hub, it was pretty ridiculous. To top it all off I had a shop put new tires on and they stripped one of the new studs the following week...if only I could strangle someone and not get arrested.
#10
Lives on the Forum
Thread Starter
Originally Posted by BoostorLose
To top it all off I had a shop put new tires on and they stripped one of the new studs the following week...if only I could strangle someone and not get arrested.
I use anti-seize on my lugnuts as well now and have had zero problems since.
#11
Lives on the Forum
Thread Starter
Originally Posted by AMRX7
Anyone know if the wheel stud sizes are the same front and rear (knurl section)?
-Andy
-Andy
Last edited by DamonB; 02-14-05 at 08:11 AM.
#12
Senior Member
Join Date: Jul 2003
Location: San Jose
Posts: 291
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by DamonB
The part numbers are the same front and rear, so yes.
-Andy
#14
Full Member
Join Date: Mar 2004
Location: Indianapolis
Posts: 144
Likes: 0
Received 0 Likes
on
0 Posts
I went with ARP wheel studs. Go with the late model F-body studs. They are 12x1.50 thread with a .509 knurl. They're also 2.5" long, allowing you to run a spacer if need be. A set of 5 is 11 bucks, and you shouldn't ever have to worry about replacing them again.
http://store.summitracing.com/defaul...=egnsearch.asp
http://store.summitracing.com/defaul...=egnsearch.asp
Thread
Thread Starter
Forum
Replies
Last Post