jacobcartmill

iTrader: (6)

http://cgi.ebay.com/ebaymotors/5ZIGE...QQcmdZViewItem


i'm assuming not since they're 10's in the back, but what about 9" ?

gergrx7

search much?

NOPR

1. go to the wheels/tires section

2. look for 'the official FC wheel fitment thread'

3. read

88IntegraLS

I'm pretty sure you can fit 10" rims in back. I've got 9's on 41 offset with more than a half inch between the rim and the spring, and it easily fits under the fender lip, 245 tires and all.

RETed

I give you a hint...
The Nissan S13's run the same kind of offset.
If it fits on an S13, it'll fit on an FC.

Watch it with the bolt pattern though.
Most S13's are 4 x 114.3!


-Ted

jacobcartmill

iTrader: (6)

i read your wheel fitment page ted, do you think those 10's will work? that would be killer

RETed

Yep, 10", +25 will fit in the back.


-Ted

The Griffin

hey Ted,you sure about that? I'm no expert but I would be more inclined to a +35mm offset in the back,unless the plan is on rolling the crap out of the wells and using a 255/40 tire or using overfenders.Even with the +35 you would need to roll the fender lip with a 275/40 tire and it's getting real close to the trailing arm also.

jn2k108

er im a noob. i dont understand this whole wheel fitment thing with offsets and all that stuff. would sum1 like to explain? i read the wheel fitment thing, and i dont understand. damn.

The AntiRice

I had those same sized, same color fn01r-c's on my fc, and they didnt fit, but then again, i did have a 285r, 255f. The fronts stuck out way too much, and the rears rubbed against my springs. They would fit with spacers though, you would prolly have to roll your fenders and maybe do a slight pull in the rear.

jacobcartmill

iTrader: (6)

antirice:

how big of a spacer?

Digi7ech

iTrader: (1)

I have 17x8 and 235/40's on my front and they BARELY fit with a 5mm spacer on 40mm offset.

I doubt those will fit up front unless you got some wide fenders to work around or kept the width to around 235/225.

37FC3S

I have those rims in bronze with 245s on 17x9 +15 in the front and 255s 17x9 +35 in the rear. I have 20mm wider fenders in front and coilovers.

jacobcartmill

iTrader: (6)

pics?

37FC3S

Here is a few pics.

RETed

I answer in the affirmative to confirm the rims will clear the inner suspension parts.
I didn't confirm if it was going to clear the fender arch. :P

It depends on the tire width, as you mentioned.


-Ted

MARTIN

what is that on the exhaust??

Jaime Enriquez

Supertrapp muffler.

jacobcartmill

iTrader: (6)

those fronts are stickin out wayy too far... back looks perfect though... you said they were 17x9 +35?

i really woulda gone with 8's in the front unless you have some more room by the springs, maybe coulda gotten a bigger offset?

Jaime Enriquez

A slightly lower offset in the rear would get the look I think he wanted, maybe both +15mm....I agree on the stance thou...fronts look a bid wierd.

turbo80cid

nice supertrapp's I have a pair waiting to be installed. how do you like the sound?
what is your exhaust setup?

I'm running a 3" downpipe to a 3" test pipe then I plan to have custom pipes bent back to the supertrapps. (this is on a turbo)

37FC3S

I think the front wheels were turned a little. The fronts are actually tucked into the fender a little. The Supertrapps are quiet and have a good tone (they sound kinda like my granny after she eats a burrito).

igottafc

iTrader: (6)

and how exactly does that sound? its like me say my exhaust sounds like a bowling ball in outerspace after it melts???

Turbo II-FB

those wheels look good ona FC