RX7Club.com - Mazda RX7 Forum

2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:
Banzai Racing

Vaccum Lines???

Thread Tools
 
Search this Thread
 
Old 02-15-03, 12:40 AM
  #1  
Senior Member

Thread Starter
 
Join Date: Jan 2003
Location: Toronto, Canada
Posts: 417
Likes: 0
Received 1 Like on 1 Post
Vaccum Lines???
Are there any other vaccum lines I could use for the Boost Gauge, I already spliced into to pressure sensor line for the blowoff valve. I have Block off Plates on all the emissions, so i seem to be running out of vaccum lines to use. Or is it possible to splice the pressure sensor line again?
HKSTurboII is offline  
Reply Like
Old 02-15-03, 12:46 AM
  #2  
controlled kaos

iTrader: (3)
 
astrochild7's Avatar
 
Join Date: Nov 2002
Location: eugene, or
Posts: 907
Received 1 Like on 1 Post
i 2nd that ????
astrochild7 is offline  
Reply Like
Old 02-15-03, 12:50 AM
  #3  
Senior Member

Thread Starter
 
Join Date: Jan 2003
Location: Toronto, Canada
Posts: 417
Likes: 0
Received 1 Like on 1 Post
Oh and where the hell is the egr valve located, it's the last plate I have to put in, and the Haynes manual doesn't show me where it is.
HKSTurboII is offline  
Reply Like
Old 02-15-03, 09:25 AM
  #4  
Senior Member

Thread Starter
 
Join Date: Jan 2003
Location: Toronto, Canada
Posts: 417
Likes: 0
Received 1 Like on 1 Post
bump
HKSTurboII is offline  
Reply Like
Old 02-15-03, 12:09 PM
  #5  
HAILERS

 
HAILERS's Avatar
 
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes on 19 Posts
The egr is located on the right rear of the intake manifold. Facing the firewall. Piece of cake to remove.
Last edited by HAILERS; 02-15-03 at 12:12 PM.
HAILERS is offline  
Reply Like
Old 02-15-03, 11:28 PM
  #6  
Senior Member

Thread Starter
 
Join Date: Jan 2003
Location: Toronto, Canada
Posts: 417
Likes: 0
Received 1 Like on 1 Post
Thanks, but is it ok to splice itno the pressure sensor vaccum line more than once? Basically putting two "t" fitting on the one line? Or is there a different vaccum line I can use?
HKSTurboII is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Inspect your aftermarket fuel pressure regulator!
t-von
3rd Generation Specific (1993-2002)
9
09-10-15 01:56 PM
replacing Oil Metering Pump lines
Blk 93
3rd Generation Specific (1993-2002)
11
09-09-15 10:56 AM
anti-skid deleted brake hard line questions
Nosferatu
2nd Generation Specific (1986-1992)
7
09-05-15 02:13 PM
How does one check a MOP(OMP)
rotor_veux
2nd Generation Specific (1986-1992)
5
09-03-15 07:10 PM
Back to Subforum
2nd Generation Specific (1986-1992)
View Next Unread
poss 13b engine siezed




Advanced Search
Quick Reply: Vaccum Lines???


Reply Closed Thread Share

All times are GMT -5. The time now is 02:00 PM.