Speed Guage wire help.
06-20-03, 01:57 PM
#1
Senior Member
Thread Starter
Join Date: Jun 2003
Location: Morgantown WV
Posts: 275
Likes: 0
Received 0 Likes
on
0 Posts
Speed Guage wire help.
I've been searching the boards for some help one replaceing the speedo wire, Since mine just went out this today. I got the part but <stupid question> where does it go? </stupid question> advanced does not sell the manuel. 
so I can't get it right now. If someone can show me a link or a write up on how to replace it it well be much happieness and rejoiceing!
Mage
so I can't get it right now. If someone can show me a link or a write up on how to replace it it well be much happieness and rejoiceing!Mage
06-20-03, 02:14 PM
#2
Glock Lover
Join Date: Mar 2001
Location: Currently residing in St Charles, MO
Posts: 2,223
Likes: 0
Received 0 Likes
on
0 Posts
Well.
The cable goes from the back of the speedo, into the side of the transmission.
Id suggest you download the factory service manual, available at www.fc3s.org
I just skimmed through it, but couldnt find the section replacing the cable is in. But it is in there! Everything is!
The cable goes from the back of the speedo, into the side of the transmission.
Id suggest you download the factory service manual, available at www.fc3s.org
I just skimmed through it, but couldnt find the section replacing the cable is in. But it is in there! Everything is!
06-20-03, 03:20 PM
#3
Senior Member
Thread Starter
Join Date: Jun 2003
Location: Morgantown WV
Posts: 275
Likes: 0
Received 0 Likes
on
0 Posts
I have it downloaded but could not find it only thing it says it to replaces it . :\ Need to get a hyens(sp) manuel but I have to order it on-line gah! thanks for the input. Might just crack her open and do what I did on the 54 (you know hammer saw and lot's of pulling! much rather have the right way tho....)
06-20-03, 07:06 PM
#6
Senior Member
Thread Starter
Join Date: Jun 2003
Location: Morgantown WV
Posts: 275
Likes: 0
Received 0 Likes
on
0 Posts
sure,
Time:10min
part :speedo cable $20.77(w/wv tax) form advanced auto parts.
Tools: philps screwdriver.
Dont for get to jack up you car to get access to trany.
1.Unscrew the guage frame (2 screws on bottem one on each side under wipers/headlights, 3 in the top of the guage area.)
2. remove and unplug wires to wipers/headlights etc (4 pull plugs)
3. remove 2?(mine only had 2 I think there are 4) screws on clear guage (you'll see them.)
4. take out guage cluster and unplug the 2 big plugs there is a clip that hold them on in the center of each plug. then unplug (or if it was like mine it was unpluged) the speedo wire.
5.under the hood look for the area it comes out (drives side just behind the steering wheel.)
6. yank wire down words to the floor. let it lay on the floor.
7. fallow the wire to the tranny (I have the 5 speed.) and unscrew the wire. option- throw the wire as far as you can I got 50feet!
8. feed the new wire throw hole to guage area. then loop it down and screw it in to the tranny.
9. reinstall guage cluster and frame in revise order.
10. make sure your wire does not hang down I losely zip tied it to the AC pipe (keep away from hot stuff!)
11.have fun.
hope that helps.
Time:10min
part :speedo cable $20.77(w/wv tax) form advanced auto parts.
Tools: philps screwdriver.
Dont for get to jack up you car to get access to trany.
1.Unscrew the guage frame (2 screws on bottem one on each side under wipers/headlights, 3 in the top of the guage area.)
2. remove and unplug wires to wipers/headlights etc (4 pull plugs)
3. remove 2?(mine only had 2 I think there are 4) screws on clear guage (you'll see them.)
4. take out guage cluster and unplug the 2 big plugs there is a clip that hold them on in the center of each plug. then unplug (or if it was like mine it was unpluged) the speedo wire.
5.under the hood look for the area it comes out (drives side just behind the steering wheel.)
6. yank wire down words to the floor. let it lay on the floor.
7. fallow the wire to the tranny (I have the 5 speed.) and unscrew the wire. option- throw the wire as far as you can I got 50feet!
8. feed the new wire throw hole to guage area. then loop it down and screw it in to the tranny.
9. reinstall guage cluster and frame in revise order.
10. make sure your wire does not hang down I losely zip tied it to the AC pipe (keep away from hot stuff!)
11.have fun.
hope that helps.
Thread
Thread Starter
Forum
Replies
Last Post
rx8volks
Canadian Forum
0
09-01-15 10:46 PM