S4 Intake elbow for FMIC
#1
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
S4 Intake elbow for FMIC
Ok I was looking over all my parts yesterday and noticed that the stock S4 T2 intake has the elbox on the TB which faces the firewall and a rubber hose that turns upwards for the TMIC...
I plan to run a FMIC and was curious if anyone sells a strait neck for the TB or if anyone sells a flange with the hose end facing the front of the car?
I have heard of the Higgi elbow however I knwo nothing about it and what its purpose is or what direction it would point in..
THX in advance guys!
I plan to run a FMIC and was curious if anyone sells a strait neck for the TB or if anyone sells a flange with the hose end facing the front of the car?
I have heard of the Higgi elbow however I knwo nothing about it and what its purpose is or what direction it would point in..
THX in advance guys!
#2
brap brap brap
iTrader: (7)
u will need to get a compression tube to go fmic sorta like this
it will elimante that crud 90* elbow that goes from tb to tmic.
http://cgi.ebay.com/ebaymotors/Gredd...spagenameZWDVW
it will elimante that crud 90* elbow that goes from tb to tmic.
http://cgi.ebay.com/ebaymotors/Gredd...spagenameZWDVW
#5
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
sounds good I appreciate your gusy input...
100.00 may seem like alot but if thats is the item holding you back from getting the FMIC installed 100.00 is what u will pay lol...
if I had a welder I would just cut the stock one and weld a pipe on the end
100.00 may seem like alot but if thats is the item holding you back from getting the FMIC installed 100.00 is what u will pay lol...
if I had a welder I would just cut the stock one and weld a pipe on the end
#6
PM HIGGI! He's running low on his TB elbows so buy them while you can.
If 100 bux is expensive to you then I recommed you go buy a car with a HUGE aftermarket.
any Honda, Nissans, FOrds, etc., etc.
If 100 bux is expensive to you then I recommed you go buy a car with a HUGE aftermarket.
any Honda, Nissans, FOrds, etc., etc.
#7
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
100.00 is a bit expensive for such a little item HOWEVER I have been in the game long enough to know that parst like this dont HAVE to be cheap.. because those who want or need it will pay the coin because there are not many options..
Trending Topics
#8
Exactly, that's cheap for a part you can't normally get by itself. You can give the Ebay knock-offs a shot and save money but I went with the Higgi elbow. Helps a forum member and you benefit. WIN-WIN.
#10
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
the n/a one will curve toward the back of the engine too..
T2 TB's point toward the drivers side..
N/a TB's oint toward the passenger side
T2 TB's point toward the drivers side..
N/a TB's oint toward the passenger side
#14
Banned. I got OWNED!!!
Thread Starter
Join Date: Aug 2006
Location: Comstock Park, MI 49321
Posts: 3,717
Likes: 0
Received 0 Likes
on
0 Posts
#15
FD Daily
iTrader: (26)
ok..have either of you even looked at this stuff in person?
have some knowledge before you call someone wrong, otherwise you really look like a fool.
notice the elbow.
http://memimage.cardomain.net/member...08_91_full.jpg
have some knowledge before you call someone wrong, otherwise you really look like a fool.
notice the elbow.
http://memimage.cardomain.net/member...08_91_full.jpg