2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

Please help. Finally started my car, 88 se, then it died

Thread Tools
 
Search this Thread
 
Old Jun 23, 2003 | 11:09 AM
  #1  
chexmix78's Avatar
Thread Starter
MENDOZA!!!!!!!!!!!!!!!!!!
Tenured Member 20 Years
 
Joined: Jun 2003
Posts: 235
Likes: 4
From: chicago
Please help. Finally started my car, 88 se, then it died

i finally started my car that had been sitting for years, it was last used by my sister. i got it jumped started it and was pleased to see it start, then i tried to move it, and it died. completely dead no power. I jumped it again and it ran until I turned it off, and then once again it was completely dead. this is why my sister stopped using it in the first place. I dont know much about cars, but it would seem to me that it is an alternator problem;perhaps the battery? I mean what else would cause it to do that? My sister told me that this was why she put it in the garage, that she tried to get it fixed got fed up with people not knowing what was wrong with it, so know I am wondering, could it be a bigger problem? I am trying to get this car running, for good so I need all the help I can get. thanx
Reply
Old Jun 23, 2003 | 11:18 AM
  #2  
Icemark's Avatar
Former Moderator. RIP Icemark.
 
Joined: Apr 2001
Posts: 25,896
Likes: 24
From: Rohnert Park CA
A couple of things:

Sounds like you have a bad battery and perhaps battery connections. If you jump started the car and removed the cables and the battery has more than a couple bad cells you may have damaged the alt as well.

Its common on most cars to have weak grounds from the factory, add 15 years to them and they are down right pathetic. One of the first things you do (after a full tune up) is to replace the grounds. That may solve the electrical problem.

Did you drain and replace the gas in it???
Any gas sitting around for "years" is most likely bad
Reply
Old Jun 23, 2003 | 11:25 AM
  #3  
chexmix78's Avatar
Thread Starter
MENDOZA!!!!!!!!!!!!!!!!!!
Tenured Member 20 Years
 
Joined: Jun 2003
Posts: 235
Likes: 4
From: chicago
thanx a lot, i am planning on getting it operational, i am actually new to this, so i am not sure what needs to be done, i am trying to do my research, but i want to do it all correctly, i was told also to check compression, how is that done exactly on rotary engines? also i am looking for like a beginners guide to rotaries, both maintenance and repair, are there any good manuals or books? thanx
Reply
Old Jun 23, 2003 | 11:34 AM
  #4  
1987RX7guy's Avatar
Eat Rice Don't Drive it.
Tenured Member: 20 Years
iTrader: (3)
 
Joined: Nov 2002
Posts: 12,752
Likes: 1
From: Laredo, Tx
www.iluvmyrx7.com
www.fc3s.org

both have the FSM online so you can check out the entire car
A haynes manual is also helpfull incase you don't have a laptop

www.howstuffworks.com search for wankel or rotary engine and you will find some good info.

Santiago
Reply
Old Jun 23, 2003 | 12:02 PM
  #5  
chexmix78's Avatar
Thread Starter
MENDOZA!!!!!!!!!!!!!!!!!!
Tenured Member 20 Years
 
Joined: Jun 2003
Posts: 235
Likes: 4
From: chicago
thanx
Reply
Old Jun 23, 2003 | 12:02 PM
  #6  
chexmix78's Avatar
Thread Starter
MENDOZA!!!!!!!!!!!!!!!!!!
Tenured Member 20 Years
 
Joined: Jun 2003
Posts: 235
Likes: 4
From: chicago
thanx
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
Jul 1, 2023 04:40 PM
Kyo
2nd Generation Specific (1986-1992)
6
Apr 13, 2019 09:24 AM
alphawolff
1st Generation Specific (1979-1985)
17
Nov 17, 2015 05:57 PM
LunchboxSA22
2nd Generation Specific (1986-1992)
37
Oct 26, 2015 10:53 AM




All times are GMT -5. The time now is 11:00 AM.