Need help, ground on engine harness to bolt on somewhere, wheres it go ??
06-18-05, 05:21 PM
#1
Need help, ground on engine harness to bolt on somewhere, wheres it go ??
Ok this is a wire that appears to be a ground, im like 99% sure it is. ITs on the engine harness and has a hole for u to bolt it on wherever u want...but i dont know where it goes ???
The other wire im unsure of is a wire connected on the firewall on the left side of the engine bay(passenger) thats a ground next to that motor thing on the firewall...im pretty sure it connects to the left back side of the tranny or motor
The other wire im unsure of is a wire connected on the firewall on the left side of the engine bay(passenger) thats a ground next to that motor thing on the firewall...im pretty sure it connects to the left back side of the tranny or motor
06-18-05, 05:25 PM
#2
Rotary Enthusiast
Join Date: Jul 2004
Location: Lubbock,Tx
Posts: 881
Likes: 0
Received 0 Likes
on
0 Posts
Hmmm, sounds like it might be the wire that bolts to one of the actual housings under the UIM. Then plugs onto a metal piece on the upper firewall on the passenger side.
That is where one of my grounds goes to. One side is oval (to housing) and the other has a connection on it (to metal piece on firewall).
Not certain if that is the one your talking about but hope it helps.
Mike
That is where one of my grounds goes to. One side is oval (to housing) and the other has a connection on it (to metal piece on firewall).
Not certain if that is the one your talking about but hope it helps.
Mike
06-18-05, 05:30 PM
#3
Originally Posted by Phantomhp
Hmmm, sounds like it might be the wire that bolts to one of the actual housings under the UIM. Then plugs onto a metal piece on the upper firewall on the passenger side.
That is where one of my grounds goes to. One side is oval (to housing) and the other has a connection on it (to metal piece on firewall).
Not certain if that is the one your talking about but hope it helps.
Mike
That is where one of my grounds goes to. One side is oval (to housing) and the other has a connection on it (to metal piece on firewall).
Not certain if that is the one your talking about but hope it helps.
Mike
one that is stray and on the firewall (left side)
the other wire is actually on the engine harness
06-18-05, 05:32 PM
#4
Rotary Enthusiast
Join Date: Jul 2004
Location: Lubbock,Tx
Posts: 881
Likes: 0
Received 0 Likes
on
0 Posts
I know the one on the firewall bolts to the housing under the UIM.
Had a brain fart and didn't notice you mentioned a second wire. I am not fully sure where that one goes to. Been awhile since I looked at my grounds.
Mike
Had a brain fart and didn't notice you mentioned a second wire. I am not fully sure where that one goes to. Been awhile since I looked at my grounds.
Mike
06-18-05, 07:07 PM
#5
Originally Posted by Phantomhp
I know the one on the firewall bolts to the housing under the UIM.
Had a brain fart and didn't notice you mentioned a second wire. I am not fully sure where that one goes to. Been awhile since I looked at my grounds.
Mike
Had a brain fart and didn't notice you mentioned a second wire. I am not fully sure where that one goes to. Been awhile since I looked at my grounds.
Mike
the other wire i have no clue where it is going to , and i dont want to install everything then not beable to put it on , or install it and put it in the wrong place and not beable to remove and move it to where it goes
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
befarrer
Microtech
3
08-22-15 05:52 PM
