Moded 88 GTU vs moded 00' Civic Si
Thread Starter
Full Member
Joined: Mar 2001
Posts: 103
Likes: 0
From: Bay Area
Moded 88 GTU vs moded 00' Civic Si
well the other day i raced a 00 Civic Si (vtec) 2/3 runs, and lost 2 times (very bad start both times) last race tied, i had a decent start, we only got upto 55-60 or so, i only have i/h/e, he has i/h/e power pulleys, AEM fuel rail, Venom Injectors. but he is getting cams and cam gears, but next time i want to run away from him, what should i do? i have these mods in mind
1. Remove 6port sleeves
2. Ported 89 intake manifold
3. Removing A/C
4. Redline oil in tranny and diff (more hp to the ground)
5. Putting my e-fan and UD Pulley on
6. ACT Clutch, 9lb Flywheel
7. Crane Hi-6
8. G-Force ECU will help?
9. wait for Agent_D's cold ram air
think thats enough?
1. Remove 6port sleeves
2. Ported 89 intake manifold
3. Removing A/C
4. Redline oil in tranny and diff (more hp to the ground)
5. Putting my e-fan and UD Pulley on
6. ACT Clutch, 9lb Flywheel
7. Crane Hi-6
8. G-Force ECU will help?
9. wait for Agent_D's cold ram air
think thats enough?
Rotary Enthusiast
Joined: Mar 2001
Posts: 1,273
Likes: 0
From: Ft. Worth, Texas, USA, Earth, Solar System...
Re: Moded 88 GTU vs moded 00' Civic Si
Originally posted by Rx7Boi
well the other day i raced a 00 Civic Si (vtec) 2/3 runs, and lost 2 times (very bad start both times) last race tied, i had a decent start, we only got upto 55-60 or so, i only have i/h/e, he has i/h/e power pulleys, AEM fuel rail, Venom Injectors. but he is getting cams and cam gears, but next time i want to run away from him, what should i do? i have these mods in mind
1. Remove 6port sleeves
2. Ported 89 intake manifold
3. Removing A/C
4. Redline oil in tranny and diff (more hp to the ground)
5. Putting my e-fan and UD Pulley on
6. ACT Clutch, 9lb Flywheel
7. Crane Hi-6
8. G-Force ECU will help?
9. wait for Agent_D's cold ram air
think thats enough?
well the other day i raced a 00 Civic Si (vtec) 2/3 runs, and lost 2 times (very bad start both times) last race tied, i had a decent start, we only got upto 55-60 or so, i only have i/h/e, he has i/h/e power pulleys, AEM fuel rail, Venom Injectors. but he is getting cams and cam gears, but next time i want to run away from him, what should i do? i have these mods in mind
1. Remove 6port sleeves
2. Ported 89 intake manifold
3. Removing A/C
4. Redline oil in tranny and diff (more hp to the ground)
5. Putting my e-fan and UD Pulley on
6. ACT Clutch, 9lb Flywheel
7. Crane Hi-6
8. G-Force ECU will help?
9. wait for Agent_D's cold ram air
think thats enough?
Get rid of some weight.
Brad
OG
Joined: Mar 2001
Posts: 1,350
Likes: 0
From: Charlotte NC
Originally posted by RotaryMan88
That redline oil stuff actually does get more HP to the ground??? I've never used it.....interesting
That redline oil stuff actually does get more HP to the ground??? I've never used it.....interesting
As for the Diff, since it is a 88GTU, if I'm not mistaken, it has an LSD diff. The Redline fluid will make the rear run smoother and make the LSD act as it should. It would also lower temps back there.
As far as HP with either of these? I doubt it. Maybe 1/4HP in friction reduction.
Throw in a 50 shot of NOS =)
Thread Starter
Full Member
Joined: Mar 2001
Posts: 103
Likes: 0
From: Bay Area
Originally posted by fc3s.org
Throw in a 50 shot of NOS =)
Throw in a 50 shot of NOS =)
Dave, you put a 50 shot on the Project '86 right? how much did it cost?
was it hard to install?
what should i take off to lose some weight? a/c, that crap under the seats, 17lb sparco racing seats, hey i heard the stock seats weigh 50lbs each!!
plus my three 10" mtx subs dont help
Last edited by Rx7Boi; Aug 16, 2001 at 04:13 AM.
Thread Starter
Full Member
Joined: Mar 2001
Posts: 103
Likes: 0
From: Bay Area
Originally posted by Rx7Boi
For sure a 50 shot, oh my engine is also starting to die... soo.. i'm going to throw in some Auto trans fluid to help it..
Dave, you put a 50 shot on the Project '86 right? how much did it cost?
was it hard to install?
what should i take off to lose some weight? a/c, that crap under the seats, 17lb sparco racing seats, hey i heard the stock seats weigh 50lbs each!!
plus my three 10" mtx subs dont help
For sure a 50 shot, oh my engine is also starting to die... soo.. i'm going to throw in some Auto trans fluid to help it..
Dave, you put a 50 shot on the Project '86 right? how much did it cost?
was it hard to install?
what should i take off to lose some weight? a/c, that crap under the seats, 17lb sparco racing seats, hey i heard the stock seats weigh 50lbs each!!
plus my three 10" mtx subs dont help
Thread
Thread Starter
Forum
Replies
Last Post
24seven_dada
3rd Generation Specific (1993-2002)
20
Nov 10, 2018 12:03 PM
befarrer
Adaptronic Engine Mgmt - AUS
3
Sep 22, 2015 09:33 AM