J-Spec Swap: Have Fuel, Have Spark, Doesn't Start
#1
Rotary Enthusiast
Thread Starter
iTrader: (1)
Join Date: Aug 2005
Location: Canada
Posts: 1,315
Likes: 0
Received 0 Likes
on
0 Posts
J-Spec Swap: Have Fuel, Have Spark, Doesn't Start
Well, my car wont start.
I tried it yesterday for the first time and it started fine, until it died 7 seconds later. Now, it wont start anymore.
I have spark, I have fuel, but no go.
My BAC valve is making a weird sound...but still, that shouldn't make the car not start....would it?
I put oil in the bottom plud, cranked it and so on...unfludded it...5 times...still wont start.
Any Ideas?
I tried it yesterday for the first time and it started fine, until it died 7 seconds later. Now, it wont start anymore.
I have spark, I have fuel, but no go.
My BAC valve is making a weird sound...but still, that shouldn't make the car not start....would it?
I put oil in the bottom plud, cranked it and so on...unfludded it...5 times...still wont start.
Any Ideas?
#5
Rotary Enthusiast
Thread Starter
iTrader: (1)
Join Date: Aug 2005
Location: Canada
Posts: 1,315
Likes: 0
Received 0 Likes
on
0 Posts
Fuel lines are ok, and if I had leaks in my IC it would start, try to keep up and then die.
It just doesn't plain start...doesn't even hesitate, just like if it was really Badly fludded...I dont know....
Guess I'll have to try that ATF unfludding proccess...
It just doesn't plain start...doesn't even hesitate, just like if it was really Badly fludded...I dont know....
Guess I'll have to try that ATF unfludding proccess...
Trending Topics
#8
Rotary Enthusiast
Thread Starter
iTrader: (1)
Join Date: Aug 2005
Location: Canada
Posts: 1,315
Likes: 0
Received 0 Likes
on
0 Posts
Ok....so I made other tests.
Got my compression again to be 100% sure.
Turns out I have 120 PSI in rear rotor and 118 on front rotor.
I have gas, I have air and I have spark...
So my question is: WTF!!!!
I think my BAC valve is faulty, but that couldn't keep my engine from starting atleast....which it did 2 days ago...
Could my gas have turn bad? I run premix and it has been sitting there for 8 months...I have about 8 litres left only...But if the gas turned bad, I figure that the car would atleats hesitate...no?
Got my compression again to be 100% sure.
Turns out I have 120 PSI in rear rotor and 118 on front rotor.
I have gas, I have air and I have spark...
So my question is: WTF!!!!
I think my BAC valve is faulty, but that couldn't keep my engine from starting atleast....which it did 2 days ago...
Could my gas have turn bad? I run premix and it has been sitting there for 8 months...I have about 8 litres left only...But if the gas turned bad, I figure that the car would atleats hesitate...no?
#9
Rotary Enthusiast
Thread Starter
iTrader: (1)
Join Date: Aug 2005
Location: Canada
Posts: 1,315
Likes: 0
Received 0 Likes
on
0 Posts
Or maybe my timing is completly off...!!!
I replace my leading coil. Since its not from an S4, but an S5, could that be a reason for having bad timing? And would that prevent my car from starting?
I figure that if it was a timing issue, the car would atleast hesitate to start....
I replace my leading coil. Since its not from an S4, but an S5, could that be a reason for having bad timing? And would that prevent my car from starting?
I figure that if it was a timing issue, the car would atleast hesitate to start....
#10
Will drive for parts
iTrader: (4)
Spark plug wires going to the right plugs?
So, it turns over, but won't fire and start, right? I just swapped in a rebuilt motor this week and them same thing happened to me. Did a double check of the plug wires and had T2 going to T1 and L2 was on loose. Got that all settled and runs like a champ now
So, it turns over, but won't fire and start, right? I just swapped in a rebuilt motor this week and them same thing happened to me. Did a double check of the plug wires and had T2 going to T1 and L2 was on loose. Got that all settled and runs like a champ now
#11
We're All Fkd..
iTrader: (16)
i know what you mean, i just did a swap and the same **** is happening to me..i dont know what the hell it is..pisses me off..i hope you figure it out so i can do it too..lol, as far as im concerned i have no idea, i went down the list and no go..my problem is i do the atf trick and it starts but when i turn it off it wont start again..lame
:AA:
:AA:
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM