HELP-Need pic of S5 T2 intake setup
03-04-04, 02:59 AM
#1
HELP-Need pic of S5 T2 intake setup
I know this sounds kinda stupid, but I am ALMOST finished with my T2 conversion, only I cannot find a diagram or pic of the intake hoses for the engine. Basically, I need to know where the 2 hoses go leaving the intercooler on the pass. side, where they go to and from the BAC, the BOV and the 3 holes I have in my intake elbow.
Here is a thread from the FC3S site, and although Dale kinda helped, I really need a visual reference:
http://www.teamfc3s.org/forum/showth...threadid=25831
I just need either a diagram or a few close-up pics of the set-up, especially the BOV and intake duct...plus coming and going to the boost sensor. I searched the FSM without luck.
If you have trouble posting pics, please send to my e-mail at Gene64030@yahoo.com
Thanks
Here is a thread from the FC3S site, and although Dale kinda helped, I really need a visual reference:
http://www.teamfc3s.org/forum/showth...threadid=25831
I just need either a diagram or a few close-up pics of the set-up, especially the BOV and intake duct...plus coming and going to the boost sensor. I searched the FSM without luck.
If you have trouble posting pics, please send to my e-mail at Gene64030@yahoo.com
Thanks
03-04-04, 06:16 AM
#2
Back from teh deadly!
Join Date: Feb 2001
Location: Louisville KY 40299
Posts: 1,163
Likes: 0
Received 0 Likes
on
0 Posts
03-05-04, 01:21 AM
#6
SOLD THE RX-7!
Join Date: Mar 2001
Location: Vancouver, BC, Canada
Posts: 7,451
Likes: 0
Received 0 Likes
on
0 Posts
sticking straight up outa the turbo is a rubber connector. then a short 6" pipe with 2 big 1/4-1" or so nipples. one of these is for the bac vavle hose (few inches long). and one is for the BOV (which then connects to the TID between the turbo and AFM). straight up from the 6" pipe there is a 90 degree rubber connecter that goes from the 6" pipe to the IC. on the drivers side there is another 90 degree connector that goes from the IC to the TB.
03-05-04, 01:55 AM
#7
Thanks Scott for replying but I need a visual of some sort. I have at least 10 places where this hose can go and that hose could go...and I am so frustrated that I did the entire swap in 3 days, yet it has been some 10 days since I can't figure out the intake. I spent more than 2 hours last night trying this and that, and I've decided that a pic or diagram can't be too hard...
Does anyone have a digital camara???
Does anyone have a digital camara???
Trending Topics
03-05-04, 05:41 AM
#8
Back from teh deadly!
Join Date: Feb 2001
Location: Louisville KY 40299
Posts: 1,163
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Dlbgirl
I have the FSM on CD and have looked through it without finding what I need. If I missed it, could someone tell me which chapter and page. A quick pic or two, or a diagram would really help.
I have the FSM on CD and have looked through it without finding what I need. If I missed it, could someone tell me which chapter and page. A quick pic or two, or a diagram would really help.
I kinda really doubt this, but whatever.
Next time try looking a little harder
03-06-04, 05:50 PM
#9
I appreciate everyone's attempt to help, but this will be my last bump on this site for this. I guess I should say that I have I received the engine without all the intake hoses, and it had a cone air filter which I am going back to stock for the fewest complications. Anyway, I don't know how it's supposed to look. I have about 20 hoses but I am sure I am missing some, so it's like a puzzle that you don't know what your building, just that you're missing some pieces and have some extras. I have seen the FSM diagram several times and it just doesn't help ME. I don't know which size hose go where and if I could just see an actual picture...mainly at the BOV, coming off the left rear intercooler, and the 3 holes I have in my intake duct...My car has been sitting for almost 2 weeks, and I'm dying to feel those 40 extra horses
