2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

HELP!!! Door wont open!

Thread Tools
 
Search this Thread
 
Old May 1, 2008 | 08:50 PM
  #1  
LBC_FC3S's Avatar
Thread Starter
Compita Racing
Tenured Member 15 Years
iTrader: (17)
 
Joined: Nov 2007
Posts: 1,123
Likes: 0
From: LBC
HELP!!! Door wont open!

so i was washing my car then decided to clean the interior. i finally finished and i was ready to leave i closed the passenger side door and i forgot to put something in and i go back to try to open it and it doesnt. is there some way to open it?
Reply
Old May 1, 2008 | 08:55 PM
  #2  
87 t-66's Avatar
not a drifter
Tenured Member: 20 Years
iTrader: (133)
 
Joined: Jun 2004
Posts: 9,337
Likes: 6
From: Columbus, Ohio
unlock it.
Reply
Old May 1, 2008 | 08:57 PM
  #3  
DragonRx7's Avatar
Goes *round*round*round*
Tenured Member 05 Years
 
Joined: Apr 2003
Posts: 718
Likes: 0
From: San Antonio
Get in the driver side.
Reply
Old May 1, 2008 | 09:13 PM
  #4  
HAILERS's Avatar
HAILERS
Tenured Member 10 Years
 
Joined: May 2001
Posts: 20,563
Likes: 27
From: FORT WORTH, TEXAS,USA
Are you saying it won't open from the outside NOR the inside????????? That's not good at all. That would be more than a outer door handle being broken.
Reply
Old May 1, 2008 | 09:30 PM
  #5  
red_s5_fc3s's Avatar
Red and Gold
Tenured Member: 15 Years
 
Joined: Sep 2006
Posts: 1,257
Likes: 0
From: Irvine, CA
If all else fails, just remove the door panel from the inside. It will be tricky, but it can be done. From there you'll have a better idea of what is going wrong.
Reply
Old May 2, 2008 | 01:13 AM
  #6  
LBC_FC3S's Avatar
Thread Starter
Compita Racing
Tenured Member 15 Years
iTrader: (17)
 
Joined: Nov 2007
Posts: 1,123
Likes: 0
From: LBC
thanks. it wont open from the outide and inside. luckily i had taked out most of the scews out and replace only a few.

when i lift the handle to open it it feels loose.

ill try to figure it out...
Reply
Old May 2, 2008 | 01:18 AM
  #7  
red_s5_fc3s's Avatar
Red and Gold
Tenured Member: 15 Years
 
Joined: Sep 2006
Posts: 1,257
Likes: 0
From: Irvine, CA
The only thing the handles are doing, are providing a lever to pull a metal rod, which opens the latch. Try to open up the door panel as much as you can and pull on the rod. If the door doesn't open, the latch might be bent or stuck.
Reply
Old May 2, 2008 | 01:36 AM
  #8  
LBC_FC3S's Avatar
Thread Starter
Compita Racing
Tenured Member 15 Years
iTrader: (17)
 
Joined: Nov 2007
Posts: 1,123
Likes: 0
From: LBC
ill give it a try tomorrow. thanks again...
Reply
Old May 2, 2008 | 01:25 PM
  #9  
LBC_FC3S's Avatar
Thread Starter
Compita Racing
Tenured Member 15 Years
iTrader: (17)
 
Joined: Nov 2007
Posts: 1,123
Likes: 0
From: LBC
***update!***

found out what the problem was. there is a spring that connects two moving parts of the mechanism. turns out that one of the hooks on the spring broke. i figured it out after about 15mins. it took long because it was in a very tight spot...
Reply
Old May 2, 2008 | 03:37 PM
  #10  
red_s5_fc3s's Avatar
Red and Gold
Tenured Member: 15 Years
 
Joined: Sep 2006
Posts: 1,257
Likes: 0
From: Irvine, CA
Sweet! Now go to Mazdatrix and get it fixed!
Reply
Old May 2, 2008 | 04:50 PM
  #11  
LBC_FC3S's Avatar
Thread Starter
Compita Racing
Tenured Member 15 Years
iTrader: (17)
 
Joined: Nov 2007
Posts: 1,123
Likes: 0
From: LBC
i used to same spring lol its ok for now still i pull a few from the junk yards.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
Sep 16, 2018 07:16 PM
doritoloco
New Member RX-7 Technical
7
Sep 5, 2015 12:41 PM




All times are GMT -5. The time now is 12:00 AM.