hellllp wont start wont even turn over.....
01-23-06, 01:24 PM
#1
Full Member
Thread Starter
Join Date: May 2005
Location: cold
Posts: 207
Likes: 0
Received 0 Likes
on
0 Posts
hellllp wont start wont even turn over.....
what happened was that i was traking off my turbo and waste gate to port the waste gate so i had taken off the TID pipe and BOV and intercooler elbow pipe.....but i never really had enough space in my garage so i decided to rent out a storage space....so i started putting everything back together and now it wont start.......is it because the AFM sensors arent in properly.....mind u that when i started doing this....the car was running perfectly.......i dunno i need suggestions.....the car wont even start all it does is clicks.....
these are the three parts i took off
helllp me plzzzzzz
these are the three parts i took off
helllp me plzzzzzz
01-23-06, 01:33 PM
#3
HAILERS
Join Date: May 2001
Location: FORT WORTH, TEXAS,USA
Posts: 20,563
Likes: 0
Received 21 Likes
on
19 Posts
No real problem. Could be a LOW BATTERY. Or it could be the starter solenoid is taking a dump.
If the battery is good, then try this. Put the car in fifth gear and brake off. Shove the car a half foot one way or the other. Then try the starter once again.
Before doing that, you might put the car in neutral. Then grab the front pulley or the belts and MAKE SURE you can turn the engine over some. Just a round or two will confirm you did not FOD your engine. IF the engine won't turn over by hand, then you've possibly left some THING in the rotating parts. Not likely, you being as careful as you usually are. But, things do happen. Bad things.
If the battery is good, then try this. Put the car in fifth gear and brake off. Shove the car a half foot one way or the other. Then try the starter once again.
Before doing that, you might put the car in neutral. Then grab the front pulley or the belts and MAKE SURE you can turn the engine over some. Just a round or two will confirm you did not FOD your engine. IF the engine won't turn over by hand, then you've possibly left some THING in the rotating parts. Not likely, you being as careful as you usually are. But, things do happen. Bad things.
01-23-06, 01:41 PM
#4
Full Member
Thread Starter
Join Date: May 2005
Location: cold
Posts: 207
Likes: 0
Received 0 Likes
on
0 Posts
hmmm i made sure i didnt leave anything loose in the engien and checked the pipes.....i jus hooked up my battery charger so i will wait a few min and then go try again.......but i dunno how to turn the engine over by hand......and i made sure i was real careful with putting the parts back on......
hmmm i dunno what the problem.....cud it also be the fact that the TID might not be on ttight enough or i fucked up an AFM sensor...
hmmm i dunno what the problem.....cud it also be the fact that the TID might not be on ttight enough or i fucked up an AFM sensor...
06-24-07, 01:47 PM
#5
Banned. I got OWNED!!!
Join Date: Mar 2005
Location: san antonio TX
Posts: 526
Likes: 0
Received 0 Likes
on
0 Posts
you'd be suprized of what you leave off sometimes. i left off the large tube that runs to the BACV. huge vac line. but if your not even turning over... check the battery. make sure that the large black wire is fully connected. also make sure the button at the end of your clutch pettal is working correctly. it wont turn over unless that button completes the circuit.
after that. idk what to tell ya
after that. idk what to tell ya
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM