Goopy street motor build and R&D
#251
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
Yeah I actually have 2 garages but my dad has his trailer in my other one I got lucky my motor was on the stand I also didn't have to drill a hole it kept the mess to a minimum I just removed the coolant nipple
I'm trying to get him to trade me those wheel they 265 In the rear and 245 upfront u can't even spin them if u tried I told him I'd give him my porshe wheels but he's a ***.
I'm trying to get him to trade me those wheel they 265 In the rear and 245 upfront u can't even spin them if u tried I told him I'd give him my porshe wheels but he's a ***.
#253
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
It a gxl. No sunroof. Got it off the original ower with all original books and stuff. the inside is mint. It needs some TLC but I drove it all the way back from ny state only issue is the coolant buzzer so far lol found it on craigslist
#259
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
do it I saw Johnathon today hes extra busy.
Picked up my trans today gonna clean it up and swap cross members then just waiting on my clutch should be here tuesday
Had a good time at Itos lots of sick cars there and good food
Picked up my trans today gonna clean it up and swap cross members then just waiting on my clutch should be here tuesday
Had a good time at Itos lots of sick cars there and good food
#260
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
gonna be 80 today gonna clean up my trans swap crossmembers and pull my dash apart to start wiring
also started a build thread for tubby
https://www.rx7club.com/2nd-generation-specific-1986-1992-17/my-na-tii-project-949632/
also started a build thread for tubby
https://www.rx7club.com/2nd-generation-specific-1986-1992-17/my-na-tii-project-949632/
#261
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
Got alot done today.
Swapped and cleaned the new trans stuff.
Removed my actual insturment cluster and and performed swapping operations to make it into the modded cluster I had previously done. Ill post pix tomorrow of how awsome everything looks..
I ran all the wires to my new guages, just need to hook up power, ground and ziptie/ cleanup excess wires once the motors back in, Ill know the actual wire lenghts...
Tomorrow I should be getting my clutch, so if I can get the motor out of my basement they'll be going back into the car and the last of the wiring will be done!!!
Swapped and cleaned the new trans stuff.
Removed my actual insturment cluster and and performed swapping operations to make it into the modded cluster I had previously done. Ill post pix tomorrow of how awsome everything looks..
I ran all the wires to my new guages, just need to hook up power, ground and ziptie/ cleanup excess wires once the motors back in, Ill know the actual wire lenghts...
Tomorrow I should be getting my clutch, so if I can get the motor out of my basement they'll be going back into the car and the last of the wiring will be done!!!
#262
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
well Im happier then a pig in **** got my clutch today, and did a bunch more wiring.
now I just need some help getting this motor out of my basement so I can put it back together...
Did all I can for now.... started working on tubby's NA tII project
now I just need some help getting this motor out of my basement so I can put it back together...
Did all I can for now.... started working on tubby's NA tII project
#268
Rotary Freak
Thread Starter
iTrader: (2)
Join Date: Mar 2006
Location: Wayne NJ
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
well 45min to get it in and couple of hours to mock everything up. tomorrow ill tighten everything down and do a few other things heres a bad shot of my cluster and some motor pix