Good source for vacuum
#1
Rotary Freak
Thread Starter
Join Date: Mar 2001
Location: LA.,California USA
Posts: 1,611
Likes: 0
Received 0 Likes
on
0 Posts
Good source for vacuum
I have done some search and did not see the answer i was looking for.. I already pulled out all my emmision components and blocked them off. Im running T04B, E6K, boost controller, HKS standard wastegate, Blitz BOV, boost gauge,and SX FPR...
Now i need to find a good vaccum source for all this parts. I know there are vacuum sources on both sides of the upper plenum but i was also told that i can use the nipple above the BACvalve. This is the one that runs diagonally and points towards the firewall. Another source i was told will be the small nipple below the BACvalve right where it meets with the LIM.
Here is what i am planning to do.. And pls correct me if i am wrong or if this will not work..
I am going to use the upper vac source above the BACvalve for my Blitz BOV and EVC4 (HKS says on the manual not to use the same vac source for FPR).
And MAP, boost gauge, and FPR on the smaller nipple below the BAC valve.. If i have all this things Teed off together will it still supply the same pressure??????...
Do you guys think this will work or i really have to use the ones on the upper plenum??..if so which ones should i use???..
Yes i did SEARCH but non of them talked about using the ones near the BAC VALVE..Thanks!..FCTURBO2
Now i need to find a good vaccum source for all this parts. I know there are vacuum sources on both sides of the upper plenum but i was also told that i can use the nipple above the BACvalve. This is the one that runs diagonally and points towards the firewall. Another source i was told will be the small nipple below the BACvalve right where it meets with the LIM.
Here is what i am planning to do.. And pls correct me if i am wrong or if this will not work..
I am going to use the upper vac source above the BACvalve for my Blitz BOV and EVC4 (HKS says on the manual not to use the same vac source for FPR).
And MAP, boost gauge, and FPR on the smaller nipple below the BAC valve.. If i have all this things Teed off together will it still supply the same pressure??????...
Do you guys think this will work or i really have to use the ones on the upper plenum??..if so which ones should i use???..
Yes i did SEARCH but non of them talked about using the ones near the BAC VALVE..Thanks!..FCTURBO2
#5
Rotary Freak
Thread Starter
Join Date: Mar 2001
Location: LA.,California USA
Posts: 1,611
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by RiceRocket
jsut hire jenna jamesone to lie on your hood naked and suck thru a hose to give you vacuum. she coudl suck a marble thru a drinking straw.
jsut hire jenna jamesone to lie on your hood naked and suck thru a hose to give you vacuum. she coudl suck a marble thru a drinking straw.
#6
Livin loud like TIMMAAAYY
Join Date: May 2002
Location: Roper, North Carolina
Posts: 1,451
Likes: 0
Received 0 Likes
on
0 Posts
hey, a little comic relief never hurt anyone. haha
but in all seriousness. there are plenty of vacuum sources. if you can get your hands on a FSM that shoul help you identify most or all of them
but in all seriousness. there are plenty of vacuum sources. if you can get your hands on a FSM that shoul help you identify most or all of them
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM