engine bay clean up tips
#1
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
engine bay clean up tips
when i remove my engine soon i would like to know what you people use to clean the relay's and other parts under the hood. i will be installing a haltech, polishing the manifolds, powedercoating brackets and pullies. but i was wondering how you clean up the other misc. pieces under the hood that cant be powdercoated and such.
the parts under my hood have the calcium deposits/ build up and i was wondering if anyone else had thos problem and what you used to clean them? there are a few relay's/ sensors near the brake booster and such...how did you clean them?
the parts under my hood have the calcium deposits/ build up and i was wondering if anyone else had thos problem and what you used to clean them? there are a few relay's/ sensors near the brake booster and such...how did you clean them?
#2
It's only Rock and Roll
iTrader: (1)
Join Date: Sep 2004
Location: In a house...
Posts: 2,509
Likes: 0
Received 0 Likes
on
0 Posts
I don't know if this will help or not.
http://autopia.org/forum/guide-detai...detailing.html
*edit* some links from there to some other places also it looks like that may have more info.
http://autopia.org/forum/guide-detai...detailing.html
*edit* some links from there to some other places also it looks like that may have more info.
Last edited by Turbo II; 03-09-07 at 08:19 PM.
#5
tom port.. AKA streetport
Thread Starter
iTrader: (6)
Join Date: Jan 2005
Location: ludlow, pa
Posts: 4,659
Likes: 0
Received 0 Likes
on
0 Posts
it would have to be a pretty soft wheel wouldnt it?
i dont want to remove piant, just calcium and grime.
good idea though!
ill go and talk to the people at the parts store and see what they have.
i dont want to remove piant, just calcium and grime.
good idea though!
ill go and talk to the people at the parts store and see what they have.
#6
Taste great, more filling
iTrader: (1)
Join Date: Feb 2005
Location: Dallas, TX
Posts: 2,012
Likes: 0
Received 0 Likes
on
0 Posts
If you're just wanting to clean and not wanting to repaint, then the best answer is probably a scotch-brite pad (thin green pads that come 3 for $2) and an economy sized bottle of dish soap. That's what I've been using, but I'm following up with a razorblade scraper and wetsanding at 320 because I'm repainting the whole thing. I picked up a gallon of "Purple Power Degreaser" at O'Reilly's for $8, but the 99 cent dishsoap just cuts so much better.
In fact, if you take the dishsoap and drizzle it directly on the panel, then go get your water hose and spray it off - it'll usually take all the grease off without rubbing - but just in the lines where the soap actually was.
In fact, if you take the dishsoap and drizzle it directly on the panel, then go get your water hose and spray it off - it'll usually take all the grease off without rubbing - but just in the lines where the soap actually was.
#7
Engine, Not Motor
iTrader: (1)
Join Date: Feb 2001
Location: London, Ontario, Canada
Posts: 29,789
Likes: 0
Received 108 Likes
on
91 Posts
Oh, if you just want to clean parts up without stripping them then it's easy. I had assumed you wanted to remove rust and then repaint...
Just use Castrol Super Clean and a stiff plastic brush. Mix the Super Clean 50/50 with water and then brush. Works wonders.
Just use Castrol Super Clean and a stiff plastic brush. Mix the Super Clean 50/50 with water and then brush. Works wonders.
Thread
Thread Starter
Forum
Replies
Last Post