2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

Eating Coolant Prob (Searched)

Thread Tools
 
Search this Thread
 
Old Aug 16, 2004 | 07:32 PM
  #1  
Andrew.'s Avatar
Thread Starter
The end of an era
Tenured Member: 20 Years
Liked
iTrader: (4)
 
Joined: Dec 2003
Posts: 4,717
Likes: 6
From: Riverside, CA
Eating Coolant Prob (Searched)

Hey guys,

My S4 NA has been having a coolant problem lately. I start it up drive it around doesn't get warm 1 bit, then "add coolant" light goes off so I go and put water in it, fill it up and go on my way, It doesn't get hot at all, always at 1/4, It doesn't bubble at all (Test for a bad coolant seal), I have to add coolant alot and the engine smells like it. My guess is I have a coolant leak and the coolant drops onto my engine (no coolant on ground) and evaporates. Is this the sign of a bad seal or should I get it pressure tested? Btw the car still pulls super great and no smoke at all on start-up.

-Andrew
Reply
Old Aug 16, 2004 | 07:42 PM
  #2  
Parastie's Avatar
Mountain Rotary Mod
Tenured Member 05 Years
 
Joined: Nov 2003
Posts: 2,411
Likes: 0
From: Freaking Poland!!
Could be a leaking O-ring in the engine. I would hope it's not though because would cause a rebuild...You could try the block-weld technique if you're daring.
Reply
Old Aug 16, 2004 | 08:39 PM
  #3  
Andrew.'s Avatar
Thread Starter
The end of an era
Tenured Member: 20 Years
Liked
iTrader: (4)
 
Joined: Dec 2003
Posts: 4,717
Likes: 6
From: Riverside, CA
block-weld? what's that?

-Andrew
Reply
Old Aug 16, 2004 | 08:42 PM
  #4  
CyborgRyu's Avatar
Drift FC
Tenured Member 10 Years
iTrader: (8)
 
Joined: Nov 2003
Posts: 1,602
Likes: 1
From: Cincinnati, OH
eh....leave the car running and do some searching? I know mine is losing coolant, but thats because of the radiator cap is messed up, so it spits out **** from the neck.
Reply
Old Aug 16, 2004 | 08:46 PM
  #5  
SilverBullet88's Avatar
Junior Member
Tenured Member 05 Years
 
Joined: Aug 2004
Posts: 41
Likes: 0
From: Daytona
yeh mine did that same thing until i baught one of those caps that has the release pressure tabs on it. it will still spew out if your not careful when you open it.
Reply
Old Aug 16, 2004 | 09:01 PM
  #6  
WAYNE88N/A's Avatar
Lives on the Forum
Tenured Member 05 Years
 
Joined: Feb 2004
Posts: 5,721
Likes: 3
From: Coldspring TX
Check the weep hole at the bottom of the water pump, also...
Reply
Old Aug 16, 2004 | 09:11 PM
  #7  
Parastie's Avatar
Mountain Rotary Mod
Tenured Member 05 Years
 
Joined: Nov 2003
Posts: 2,411
Likes: 0
From: Freaking Poland!!
Block-weld fix:
http://www.rotaryresurrection.com/ro...oolantfix.html
Reply
Old Aug 16, 2004 | 09:31 PM
  #8  
Andrew.'s Avatar
Thread Starter
The end of an era
Tenured Member: 20 Years
Liked
iTrader: (4)
 
Joined: Dec 2003
Posts: 4,717
Likes: 6
From: Riverside, CA
CyborgRyu,

I'll do that tommorow

Wayne,

I'll check that out, I hope its a basic fix

Parasite,

I'll do that if I 100% know that the seals are the problem.

-Andrew
Reply
Old Aug 17, 2004 | 04:43 PM
  #9  
Andrew.'s Avatar
Thread Starter
The end of an era
Tenured Member: 20 Years
Liked
iTrader: (4)
 
Joined: Dec 2003
Posts: 4,717
Likes: 6
From: Riverside, CA
Hey if i do that seal stuff and my seals aren't bad will it just add a extra layer to it and not mess up?

-Andrew
Reply
Old Aug 17, 2004 | 05:04 PM
  #10  
DerangedHermit's Avatar
Banned. I got OWNED!!!
 
Joined: Jan 2004
Posts: 2,040
Likes: 5
From: Knoxville, TN 37916
Sounds like a coolant leak. Also, my S4 doesn't run above 1/4 temp on the gauge.
Reply
Old Aug 17, 2004 | 10:02 PM
  #11  
Andrew.'s Avatar
Thread Starter
The end of an era
Tenured Member: 20 Years
Liked
iTrader: (4)
 
Joined: Dec 2003
Posts: 4,717
Likes: 6
From: Riverside, CA
Yo,

Checked it out, put some antifreeze in there, air bleeder valve, then filled it, put the cap on and started it up, Grey smoke came out for 1 second ( I jumped to check the exhaust) and left, went to smell exhaust, didn't smell like coolant. (The car has been sitting here for a week maybe that's why it puffed for a sec) Looked under the car I saw it dripping in a few spots, got my rag cleaned it, now 2 spots, on my pan by engine, and lower rad hose. I watched it the whole time for about 20 min, eyeballed about how much coolant dropped, shut it off, waited and opened the cap, Yup I just got some hose leaks, The smell is now centered around my exhaust manifold area so i'm guessing a hose there and a lower rad hose. What a scare ey?

-Andrew
Reply
Old Aug 17, 2004 | 10:08 PM
  #12  
inflatablepets's Avatar
Rotary Enthusiast
 
Joined: Mar 2004
Posts: 1,473
Likes: 0
From: St Louis
On my car, the heater core was leaking. I noticed damp carpet on the passenger side. As a temporary fix, until I had time to rip the dash apart, I used a few teaspoons of black pepper in the system. It is not permanent, and it will flush out when you do a back flush to the system.

[Edit] Sorry, I stared typing before you posted to this.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Rocketeerbandit
SE RX-7 Forum
7
Aug 11, 2017 02:12 PM
JoesFC
2nd Generation Specific (1986-1992)
9
Oct 5, 2015 08:10 AM
04G35S
3rd Generation Specific (1993-2002)
4
Sep 9, 2015 07:05 AM
ZaqAtaq
New Member RX-7 Technical
2
Sep 5, 2015 08:57 PM




All times are GMT -5. The time now is 08:53 AM.