2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

buzzer make it go away please

Thread Tools
 
Search this Thread
 
Old Jul 19, 2006 | 11:14 PM
  #1  
stevie1020's Avatar
Thread Starter
Gig a Giddy Go
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 348
Likes: 0
From: louisiana
buzzer make it go away please

my buzzer refuses to stop. on the idiot cluster no warning lights are going off i checked all of mine fluids they are all full. i did switch up S5 dash in to the car but everything works fine except i cant figure out one harness so i havent wiered it up yet. any help would greatly be appericated and sorry ahead of time for the crapy spelling
Reply
Old Jul 19, 2006 | 11:46 PM
  #2  
Sideways7's Avatar
Lives on the Forum
Tenured Member: 20 Years
Liked
iTrader: (7)
 
Joined: Dec 2003
Posts: 6,598
Likes: 10
From: Temple, Texas (Central)
Well, depending on the harness, some of the sensors might not be hooked up right. I believe this could cause the car to think some of the fluids are low.
Reply
Old Jul 20, 2006 | 11:10 AM
  #3  
13bturbofc's Avatar
mmm doritos
Tenured Member: 15 Years
iTrader: (4)
 
Joined: Apr 2006
Posts: 2,107
Likes: 0
From: lancaster PA
did the buzzer do this only after installing the new dash?if not you may have a bad coolent or oil level sensor i had that problem
Reply
Old Jul 20, 2006 | 11:41 AM
  #4  
stevie1020's Avatar
Thread Starter
Gig a Giddy Go
Tenured Member 05 Years
 
Joined: Apr 2006
Posts: 348
Likes: 0
From: louisiana
ya it only started doing this after i put the S5 dash in ill check the sensors thank you
Reply
Old Jul 20, 2006 | 03:21 PM
  #5  
13bturbofc's Avatar
mmm doritos
Tenured Member: 15 Years
iTrader: (4)
 
Joined: Apr 2006
Posts: 2,107
Likes: 0
From: lancaster PA
u can check the sensors but if it only started after u installed the dash i wouldnt bother i would just focus on getting that harness all hooked up and go from there...im sure u can find a diagram somewhere here that should help you out.....good luck!
Reply
Old Jul 20, 2006 | 03:34 PM
  #6  
ericgrau's Avatar
Clean.
Tenured Member 10 Years
iTrader: (1)
 
Joined: Mar 2005
Posts: 2,521
Likes: 3
From: Huntington Beach, CA
If a sensor is unplugged it'll set off the buzzer. Probably not plugged into the harness, like people are saying.

Last edited by ericgrau; Jul 20, 2006 at 03:38 PM.
Reply
Old Jul 23, 2006 | 12:17 PM
  #7  
Icemark's Avatar
Former Moderator. RIP Icemark.
 
Joined: Apr 2001
Posts: 25,896
Likes: 24
From: Rohnert Park CA
did you re-pin the harnesses??? If you put a S5 dash into a S4 car, you need to re-pin the wiring harness
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
MazdaspeedR1
The Bad & Fugly Businesses
27
May 22, 2018 05:58 PM
jsesq
3rd Generation Specific (1993-2002)
27
Sep 25, 2015 11:10 AM
ray green
1st Gen General Discussion
2
Sep 2, 2015 06:35 AM




All times are GMT -5. The time now is 03:32 PM.